Ground Clearance of Curt Class III Hitch Installed on a 2011 Chrysler 300C

Question

Question:

and have read and watched all the videos on your post! Not so uncertain as I was in the beginning but I am wondering if you can tell me what the clearance is from the bottom of the hitch to the ground once installed on a completely stock 300C ? Am measuring up my trailer and the specs for where I hope to be and am wondering if you guys have ever measured it when finished! Thanks

asked by: Duane D

0

Expert Reply:

The Curt Class III hitch part # C13093 measures 10-1/2 inches from the TOP of the hitch opening down to the ground. We know this since we installed this hitch on a 2012 Chrysler 300C.

So since this is a 2 inch hitch and the lip of the hitch opening would be about 1/2 inch from the bottom of the hitch to the ground would measure right at 9 inches.

expert reply by: Jameson C

0

Answer 1

The Curt Hitch part #C13093 that you referenced has been confirmed as a fit for the 2016 Dodge Charger so it would be a great option for you. The most popular bike rack we carry that has been confirmed to fit this vehicle is the Swagman XTC2 Bike…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13093 is a confirmed fit for your 2016 Chrysler 300 and is also a fit for a few other models like the Dodge Charger and Dodge Challengers of certain model years. The towing capacity…

view full answer...

Answer 3

For the Curt Class III Trailer Hitch #C13093 on your 2013 Chrysler 300, you will not need to use any specific ball mount. The ball mount you will want to use is the one that provides the correct rise or drop needed for you to tow your trailer level.…

view full answer...

Answer 4

The picture of Curt trailer hitch #C13236 is correct but that is just one design that is available for the 2016 Dodge Challenger. Hitch #C13093 has the square tube with the receiver below the cross tube. The round tube design though, #C13236, would…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Ground Clearance of Curt Class III Hitch Installed on a 2011 Chrysler 300C

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching