Will WeatherTech No-Drill Mud Flaps Fit 2016 Ford King Ranch F-150 With Automatic Running Boards

Question

Question:

Will the no drill mud flaps fit King Ranch with automatic running boards thanks

asked by: Bill

1

Helpful Expert Reply:

The WeatherTech Mud Flaps, part # WT110044-120044 you asked about are designed to work with a 2016 F-150 if it has add-on fender flares and if there is at least 2-inches of clearance between the edge and wheel well.

When installing these mud flaps no drilling is required.

expert reply by: Jeffrey L

1

Answer 1

If you have the wheel lip molding like I have pictured below in red then you'll want to use the WeatherTech Mud Flaps #WT110044-120044 instead of the #WT110050-120050. We do have a customer review photo for this specific fit but it's a bit…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 7

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 8

Typically a suspension bolt will be measured by the shaft of the bolt not including the head, since the head of the bolt isn't used in mounting the springs. The shackles are 3-3/4" long x 1-1/2" tall overall and the bolt holes are…

view full answer...

Answer 9

It looks like your MORryde ALLTREK 4000 Shock Absorbing Equalizers #MR89DR are longer than your previous equalizers were because your leaf springs are way too close to each other. The shackles should be creating more of a "W" shape instead…

view full answer...

Answer 10

I can help you figure out how to determine the best option for a wet bolt/shackle upgrade kit, though in order to determine the correct one you will need to take a quick measurement of the shackle straps on your Jayco Jay Flight. The reason for that…

view full answer...

Answer 11

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according to…

view full answer...

Answer 12

I reached out to MORryde and the MORryde Rubber Equalizers for Tandem Axle Trailers - 35" Wheelbase - 8K #MR27ZR you were looking at is designed for 35" axle spacing and would not work with your trailer with 36" axle spacing. My…

view full answer...

Will WeatherTech No-Drill Mud Flaps Fit 2016 Ford King Ranch F-150 With Automatic Running Boards

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching