Replacement Left Rear Leg for Lippert Ground Control 3.0

Question

Question:

On my Ground Control 3.0, the left rear jack LC305339? drug and is bent between the mounting plate and the jack body. The jack works fine, it is not bent. How can I get just the steel body with the mounting plate with no internal parts? Thanks,

asked by: Michael M

0

Expert Reply:

I spoke to my contact at Lippert and the replacement leg is only available as the entire unit.

He went on to tell me that they are not set up to replace just the leg without the motor assembly, and the unit should be fully replaced with the # LC305339 for the left rear leg.

For the right rear leg you will want # LC344792.

I have linked the above mentioned products to this page for your convenience.

expert reply by: Jackie C

0

Answer 1

We do have motors that you can add to your landing gear. For example, the Landing Gear Set #RVLG-8000 can be operated with the manual crank #RVLG-HDL but you can also add the motor #LC142178 and switch #LG-145236 for effortless operation on your end.…

view full answer...

Answer 2

There will be 4 wires coming from the Lippert Replacement Electric Jack Switch #LC387874 that you are looking at. The blue wire from the switch will go to a 6 amp breaker like #LC134181 that is installed between the switch and jack motor. This will…

view full answer...

Answer 3

If you have a Lippert Ground Control leveling system on your 2016 Jayco trailer then Replacement Left Rear Leg for Lippert Components Ground Control 3.0 Electric Leveling System Item #LC305339 is the correct replacement. If it is a different brand or…

view full answer...

Answer 4

I have a couple of solutions but after contacting lippert I have found the female plug end for the Replacement Short Left Rear Leg - Ground Control 3.0 Electric Leveling System part #LC342610 is not something available separately. Solution One will…

view full answer...

Answer 5

Yes. If you were to wire the power and ground wires on the Replacement Legs #LC305339 and #LC344792 to a switch similar to the Replacement Power Switch #LC144214 you would be able to use them independently of a Lippert Ground Control system #LC358590…

view full answer...

Answer 6

I checked and found the manual for the Lippert Electric Trailer Jack #LC285318 and there was no mention of anything going in the hole beforehand to tighten them. I added a cut out of the manual for you which shows the parts for this jack, and it does…

view full answer...

Answer 7

The C-800 Replacement Klauber Motor #LC138445 that you referenced is the correct motor for your Lippert 113407 stabilizer jack system. As long as you seal up the wire connections you can splice into the wiring that you're able to access when…

view full answer...

Answer 8

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 9

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 10

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Replacement Left Rear Leg for Lippert Ground Control 3.0

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching