Replacement Left Rear Leg for Lippert Ground Control System

Question

Question:

I have a 2016 jayco 4112 and the middle left lift leg is bent. Will this part be a replacement?

asked by: Wayne

0

Expert Reply:

If you have a Lippert Ground Control leveling system on your 2016 Jayco trailer then Replacement Left Rear Leg for Lippert Components Ground Control 3.0 Electric Leveling System Item # LC305339 is the correct replacement. If it is a different brand or model let me know and I can determine if we have a replacement.

expert reply by: Michael H

0

Answer 1

I have a couple of solutions but after contacting lippert I have found the female plug end for the Replacement Short Left Rear Leg - Ground Control 3.0 Electric Leveling System part #LC342610 is not something available separately. Solution One will…

view full answer...

Answer 2

We do have motors that you can add to your landing gear. For example, the Landing Gear Set #RVLG-8000 can be operated with the manual crank #RVLG-HDL but you can also add the motor #LC142178 and switch #LG-145236 for effortless operation on your…

view full answer...

Answer 3

There will be 4 wires coming from the Lippert Replacement Electric Jack Switch #LC387874 that you are looking at. The blue wire from the switch will go to a 6 amp breaker like #LC134181 that is installed between the switch and jack motor. This will…

view full answer...

Answer 4

Yes. If you were to wire the power and ground wires on the Replacement Legs #LC305339 and #LC344792 to a switch similar to the Replacement Power Switch #LC144214 you would be able to use them independently of a Lippert Ground Control system #LC358590…

view full answer...

Answer 5

Yes, the left rear leg for the Lippert Ground Control 3.0 Electric 4 Point Leveling System is the same as the left middle leg for the Lippert Ground Control 3.0 Electric 6 Point Leveling System. If your left middle leg measures 17" long then you…

view full answer...

Answer 6

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 7

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 8

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 9

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 10

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 11

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Replacement Left Rear Leg for Lippert Ground Control System

Product Page this Question was Asked From

Continue Researching