Brake Controller Install on 2010 Toyota Highlander
Question:
I have a new v6 2010 highlander with a tow package .It has a 4pin connecter .I need to connect a brake cotroll that requires a 7 pin connecter .Is this possible ??.Thanks
asked by: john p
Expert Reply:
Installing a Brake Controller on your Highlander is certainly possible. As a first step, you will need to choose a brake controller. I would recommend the Tekonsha Prodigy P2, part # 90885. The P2 is our best selling brake controller, and is simple to use and set up.
To install the controller, we offer a Brake Controller Installation Kit, part # ETBC7. The kit contains everything necessary to complete the installation, including wire, circuit breakers, hardware and the adapter that will convert your existing 4-pole connector to a 7-way connector.
The adapter included in the kit is mounted to the rear of the vehicle, and plugged into your existing 4-pole. At this point, your lighting connections are complete. The adapter will have 4 additional wires that will need to be connected. The blue wire carries the output from the controller, and would be ran under the vehicle to the engine compartment, and ultimately through the firewall to the cab connecting to the blue wire on the controller. The white wire would be grounded to clean metal on the vehicle. The black wire is used to provide 12-volts for any trailer accessories requiring power. It would also be ran to the engine compartment and attach to the positive battery terminal via a 40 amp circuit breaker included in the install kit. The remaining purple wire is typically used for reverse lights if your trailer is equipped with them.
The controller itself would mount under the dash, typically to the right of the steering column within easy reach of the driver. The black wire would run through the firewall to the positive battery terminal via the 20 or 30 amp breaker included in the kit. If the trailer has 2-4 brake assemblies, use the 20 amp. If the trailer has 6-8 brake assemblies, the 30-amp breaker would be used. The blue wire would attach to the wire mentioned above that ran from the rear of the vehicle. The white wire attaches to the negative battery terminal, and the red wire connects to the the cold side of the brake stoplight switch located at the top of the brake pedal. To locate the correct circuit to tap this red wire into, first locate the stoplight switch. The switch will have several wires running out of it, use a circuit tester like part # PTW2993 to locate which of these wires goes hot only when the brake pedal is pressed, and tap the red wire into it.
I will include links below to some additional information about brake controllers that you might find helpful.
I will also link to a video showing an install on a 2008 FJ Cruiser. Although the install is on a different vehicle, the procedure would be very similar on your Highlander.
Products Referenced in This Question
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Q&A: Routing Power Wire Through Firewall on 2021 Toyota Highlander
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - 1 to 2 Axles - Proportional
- Shop: Universal Wiring Adapter for Curt Trailer Brake Controllers
- Search Results: trailer brake controller
- Video: Trailer Brake Controller Installation - 2012 Toyota Tundra
- Video: Redarc Tow-Pro Liberty Brake Controller Installation - 2013 Toyota Highlander
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Video: Choosing the Right Brake Controller
- Shop: Trailer Hitch
- Search Results: 44649
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Choosing the Right Trailer Wiring
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Q&A: 2022 Toyota Highlander Wiring for a 7-Way Blade Connector
- Search Results: 68149
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Search Results: brake controller
- Article: Brake Controller Installation: Starting from Scratch
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Suspension Enhancement
- Q&A: Replacement 5 Leaf Slipper Spring for a Tandem Axle Dump Trailer with Two 6K Axles
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Video: Redarc Tow-Pro Trailer Brake Controller Plug-and-Play Wiring Harness Review
- Search Results: dust cap
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: How to Choose the Right Trailer Hitch Class