What is the Torque Spec for a Nut on a 1-7/8 Inch Hitch Ball

Question

Question:

have a 1-7/8, 2000 lb hitch ball with 1-1/2inch size nut. what foot pound of torque is correct?

asked by: Barry B

0

Expert Reply:

The torque value for your 1-7/8 inch ball is going to depend on the diameter of the shank. Draw-Tite lists the following torque specs:

"During hitch ball installation, torque all 3/4" shank diameter balls to 160 ft. lbs., and 1" shank diameter balls to 250 ft. lbs., and 1-1/4" shank diameter balls to 450 ft. lbs."

expert reply by: Michael H

0

Answer 1

The Draw Tite hitch part #75782 would be the hitch I'd recommend for your 2019 Ford Escape. It is a 2 inch hitch that has a concealed crosstube with plenty of towing capacity. I attached an install video for this for you to check out as well.…

view full answer...

Answer 2

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 3

The correct torque value for the nut on a 1-7/8 inch hitch ball depends on the diameter of the shank. Draw-Tite, who makes #19256 and #19260 lists the following torque specs: "During hitch ball installation, torque all 3/4" shank diameter…

view full answer...

Answer 4

It sounds like you you have a standard 7-way trailer connector, so I recommend either the Pollak 7 Pole to 4 Way Connector Adapter #PK12716 or the Wesbar Adapter - 7-Way RV to 4-Way #707250. If you happen to have a European 7-way, then you will want…

view full answer...

Answer 5

The Buyers Products Replacement Tri-Balls #3373020620 for Adjustable Tri-Ball Hitch #3371802225 is 1" from the hitch pin center hole to the end of the hitch tube(see image). This is the same measurement for all the mounting holes as they are in…

view full answer...

Answer 6

I am sorry to hear that the tri ball portion of your Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches #D900 was stolen. You can use the Replacement Tri-Ball for CURT Adjustable Ball Mount #C45800 to replace the portion with the 3…

view full answer...

Answer 7

The side to side hole spacing of the #A10-7072VP 7-way connector is 2-1/2 inches center to center, and top to bottom is 1-13/16 inches, once again center to center. I've shown these dimensions in the provided photo. I've linked to a product…

view full answer...

Answer 8

I looked up the bolt and nut sizes that come with the Curt weight distribution system part #C17062 and the sizes you need are 3/4", 1-1/8", 1-7/8", and 9/16".

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

What is the Torque Spec for a Nut on a 1-7/8 Inch Hitch Ball

Product Page this Question was Asked From

Continue Researching