Can Fulton Fold-Away Hinge Kit be Used on Aluminum Trailer with Steel Tongue

Question

Question:

I see where the Fold away couple kit is not be used on an aluminum trailers. If I have an aluminum boat trailer with a galv. steel tongue can I mount the fold away coupler hinge kit on it?

asked by: Mike S

0

Expert Reply:

If the tongue portion of your trailer is steel then yes you can attach a hinge kit like the part # FHDPB330301 which is for 3 x 3 inch trailer tongues. Or the part # FHDPB350101 which is for 3 x 5 inch frames.

expert reply by: Jameson C

0

Answer 1

For your aluminum trailer with a galvanized steel tongue (swing-away tongues cannot be used on aluminum tongues), you'll need a die-cast steel tongue with a zinc finish from Fulton. The correct fit is going to depend on the size of your trailer…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

Oddly enough I can't find a decent u-bolt that we carry that would work well for your application.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

I have a solution for you but the part #CE10190GA-4 is not available in a half kit so what you would want is the part #CE10190GA with the swivel bracket part #CE10206G. We don't have the bolt and nut though so you would need to supply that…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Can Fulton Fold-Away Hinge Kit be Used on Aluminum Trailer with Steel Tongue

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching