Recommended Ball Mount for a 2006 Toyota Sienna Ball With a Class II Trailer Hitch
Question:
What is recommended ball hitch lift for my 2006 Toyota Sienna? Seems to ride low. I have a Class II hitch installed.
asked by: Allen
Expert Reply:
The recommended ball mount for your 2006 Toyota Sienna would have a 2-5/8 inch rise, like Curt ball mount # C45016. This would put the hitch ball at the most common trailer height, but to ensure it will work with your particular setup, I would recommend taking a couple simple measurements.
First, measure from the ground to the top of your class II hitch opening. Then, with your trailer level, measure from the ground to the flat bottom of the trailer coupler. The difference between these two measurements would be your required rise or drop.
I would advise that you check the information on your particular trailer hitch, as I notice that the class II Curt trailer we offer for your Sienna, part # C12065, would require that you use only the # C45016 ball mount in order to retain the hitch warranty. This is fairly common for the 1-1/4 inch trailer hitches.
I am including a link to a page with more information on choosing a ball mount, if needed.
Products Referenced in This Question
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 350 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Product Page this Question was Asked From
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Article: My Trailer Hitch Doesn't Fit
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Q&A: Ball Mount For 2002 Toyota Sienna With Curt Hitch C13511 For Towing U-Haul Trailer
- Q&A: Recommended Hitch for Best Ground Clearance on 2011 Toyota Sienna
- Q&A: What Hitch Gives the Highest Ground Clearance on My 2022 Toyota Sienna?
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Trailer Hitch Installation - 2015 Toyota Sienna - Curt
- Video: Curt Class II Euro Style Drawbar Review C45571
- Shop: Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
- Q&A: What Size Tap Can Be Used to Clean Weld Nuts to Install Hitch on 2004 Toyota Sienna
- Q&A: Recommended 1-1/4-Inch Class II Hitch for 2015 Toyota Sienna AWD
- Q&A: Installation Instructions for the Curt Hitch C12065 on a 2008 Toyota Sienna
- Shop: Curt Class II Euro Style Drawbar with 1-7/8" Ball - 4-5/8" Rise - 3,500 lbs
- Video: Curt Ball Mounts - Fixed Ball Mount - C45660 Review
- Video: Curt Multi-Ball Mount Review
- Shop: Gooseneck Hitch
- Search Results: ball
- Video: Choosing the Right Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: hitch
- Search Results: 90160
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Choosing the Right Brake Controller
on Trailer Hitch Ball Mount
