Recommended Stud-Mount Single-Wire Mini Rectangular LED Clearance Light For Boat Trailer

Question

Question:

Im looking for amber clearance lights for a boat trailer. I currently have a single wire stud mounted sealed LED approximately 2.5inch x 1.25. I am looking to simply remove the existing light and replace without any drilling or other modifications. Thank you.

asked by: Andy H

0

Expert Reply:

We do have a clearance light that will work for you.

I recommend the Optronics Mini Rectangular LED Trailer Clearance Light, part # MCL95AB. This is a 3-diode light that measures 2-1/8 inch x 1-1/8 inch and is 1-1/16 inch deep. It is a stud-mount single wire light with an amber lens. This light has a sealed, waterproof housing, so it will work great for your boat trailer.

expert reply by: Jeffrey L

0

Answer 1

The Optronics LED Clearance Light #MCL95AB does ground through the mounting stud. For a different yet similar light you can use #MCL13A2B with snap-on ring #A13B2B that is a 2 wire light and does have a ground wire.

view full answer...

Answer 2

The power wire on the Optronics #MCL95AB clearance light is 18 gauge, which is sufficient for the super-low power consumption of an LED lamp. To see an installation video, click the provided link.

view full answer...

Answer 3

You can still use the Optronics clearance light #MCL95AB with an aluminum frame. This light grounds through the mounting stud. In the event that you end up with a bad ground to the frame, you can attach a wire behind the mounting stud and run it to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...