What is the T-Handle on the Door Latch # L4080 Made Of?

Question

Question:

What is the t-handle itself made of? Is it stainless steel or is it chrome plated steel? Thanks

asked by: Vern

0

Expert Reply:

I spoke to my contact at Redline and he informed me that the t-handle of the Redline Door Latch # L4080, you were looking at, is chrome plated steel.

I have linked the above mentioned product to this page for your viewing and purchasing convenience.

expert reply by: Jackie C

0

Answer 1

The lid of the Bright Way Trailer Breakaway ICU Kit with 12V, 5-Amp-Hour Battery, Charger, and Wire Loom #BW94FR that you referenced has a wiring diagram shown that details how it wires. Not seen is there is a single wire that runs up to running…

view full answer...

Answer 2

Yes, to use the Bauer Products Manger Door Lock for Horse Trailers #BA95FR in a right hand configuration you'd just have to flip the latch so that the locking mechanism is on the right hand side.

view full answer...

Answer 3

Check out the dimension picture I attached for the Latch Part #L4080 that you referenced. I believe the dimension you are looking for is 1/2 inch on all sides from the edge of the latch flange to the center of the mounting holes.

view full answer...

Answer 4

The hole dimensions for the Over the Seal Strap Hinge are as follows. From the center of the hinge to the holes going down the shaft is 3-1/2", 9", and 14-1/2" respectively. So the measurement you're looking for is about 3 inches…

view full answer...

Answer 5

If the hole in your door for the handle measure 2-3/4" x 3-3/4" the #L4080 would work, but most likely you would need a handle like the part #L1883 as that is more like the latching style of your current handle. This latch installs in the…

view full answer...

Answer 6

The Redline T-Handle Door Latch, part #L4080 can be mounted in any position you choose. You will just need to make sure the latching bar will catch, wherever the door latch is mounted. The amount of throw on the latch is 1-1/2 inches. See the…

view full answer...

Answer 7

I went out to the warehouse and pulled a Replacement Locking T-Handle, #UWSTHLOCK, and took some measurements. The overall width is 4-3/4 inches. The overall height is 4-13/16 inches. The mounting holes are 3-7/8 inches apart on center from side to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

To create barn doors out of your ramp door, you will need hinges and a latch. I suggest a latch/lock system like the Universal Cam-Door Lock for Enclosed Trailers - 1" Keeper, #383200. This will use a 3/4 inch diameter pipe that you'll have…

view full answer...

What is the T-Handle on the Door Latch # L4080 Made Of?

Product Page this Question was Asked From

Continue Researching