Recommendation for 10 Foot Long Carpeted Bunk Boards for a Bass Boat Trailer

Question

Question:

Where can l find 10 ft. Bunk rails for my bass boat trailer

asked by: Glenn F

0

Expert Reply:

I have a couple of options for you to add 10 foot long carpeted bunk boards to your trailer. First, you could use 2 sets of the 5 foot long boards, # CE27820.

The other option is to get 10 foot boards locally and staple on some carpet yourself. We have different carpet options depending on what size and color you want and I have included a link to them for you.

expert reply by: Michael H

0

Answer 1

I can certainly understand not wanting to have to connect 2 five-foot carpeted bunk rails like #CE27820 to get the 10 foot bunks you need. We don't offer them in the 10' length because the shipping costs would be more expensive than the bunks…

view full answer...

Answer 2

Two 12 foot long bunks boards will work well to support your 21 foot boat. Ideally, the bunk boards should be at least half as long as your boat and run from the stern (or a few inches beyond it) to the bow as far forward as you like. Due to shipping…

view full answer...

Answer 3

Boat trailer bunk boards like CE Smith #CE27840 can be secured to swivel brackets like #CE10000G-4 using either galvanized or stainless steel hardware intended for wood. This is not included so you will source the preferred hardware locally. Lag…

view full answer...

Answer 4

The link provided will show you all available bunk boards we offer, the longest of which are 6-feet in length, part #CE27840. If you need longer bunks for your trailer you can fabricate them using lumber you source locally along with marine-grade…

view full answer...

Answer 5

For your boat trailer, the length of bunks is dependent on the boat and the trailer, so I would be hesitant to change anything from the factory. It soulds like you have a couple of 2 foot bunk boards that need to be replaced and you can use the CE…

view full answer...

Answer 6

It sounds like your trailer had a wishbone harness and/or could have multiple ground wires. On a 4-Way trailer end, the one covered pin is the ground. Next to that is the running light pin. The running light pin on some connectors will have more than…

view full answer...

Answer 7

To upgrade the axle and hubs on your Northern Hardware Trailer, I recommend looking at an Axle-Less System like the Timbren #A20RS545. This suspension system will provide you with a smooth, quiet, and safe ride and can completely eliminate the need…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

Thank you for the pictures! For a replacement option I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX29FR to replace your current actuator. The #DX29FR has a 7500lb trailer weight…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...