What Grade of Bolt is Required for Installing Timbren Spacer on Timbren Kit

Question

Question:

i have a set of TFR250SDG just wanting to know what grade of bolt they send with them. adding a 1/2 spacer to existing one and want to make sure i have right grade of bolt. would grade 2 to work or do i need grade 5 or 8 thanks

asked by: Ron R

0

Expert Reply:

Grade 5 or 8 would be fine for installing a 1/2 inch Timbren spacer part # TA25722-90P00 with the Timbren kit part # TFR250SDG you have. You will need to find this at a local hardware store.

expert reply by: Jameson C

0

Answer 1

Yes, the correct Timbren kit for your 2016 Ford F-250 4 wheel drive is the part #TFR250SDG that you referenced. We have some of the fits separated by 4WD or 2WD since some of them only fit one or the other, but the Timbren kit fits both styles.

view full answer...

Answer 2

Since the Timbren Rear Suspension Enhancement System #TFR250SDG will mount on the bottom of the frame on your 2016 Ford F-250 and the B&W Gooseneck Hitch #BWGNRK1111 installs on the side of the frame they will be compatible with each other.

view full answer...

Answer 3

The Timbren #TGMRTT35D are 5-9/16" tall.

view full answer...

Answer 4

Timbren likes to recommend 1 inch between the axle and the Timbren when the truck is unloaded. We have found that this works the best. This allows the suspension to feel when the vehicle is unloaded and still gives you support when needed when…

view full answer...

Answer 5

The Timbren Rear Suspension Enhancement System part #TGMRCK25D which is a fit for a 2018 GMC Sierra 2500 will measure 5-1/4" tall without the 1" spacer or 6-1/4" tall with the 1" spacer. I have attached a photo below. The springs…

view full answer...

Answer 6

I spoke to my contact at Timbren, I explained your situation and they said that in your situation you could go ahead and use the Timbren System part #TFR250SDF. The mounting bracket is the same as the #TFR250SDG with the only difference being the 1…

view full answer...

Answer 7

The ideal gap between the bottom of the jounce bumper and top of the contact point is about 1/2"-1" but you can go more if you don't want them to engage as soon or as often. Therefore, in lifted applications you'll need to use…

view full answer...

Answer 8

The correct Timbren Rear Suspension Enhancement System for a 2013 Ford F-250 is part #TFR250SDG. The overall height of the assembly is 6-1/2" per Timbren. The 1" of space you have between the frame and bump stop should not altered the…

view full answer...

Answer 9

We have found that it varies a little bit between vehicles. For some vehicles the unloaded ride quality is totally unaffected with the Timbrens. Typically this is on higher capacity vehicles where the suspension is already pretty stiff and…

view full answer...

Answer 10

The Timbren Rear Suspension Enhancement System #TGMRCK25D you were looking at for your 2013 Chevrolet Silverado 2500HD 4x4 are 5-1/4" tall without the 1" spacer, or 6-1/4" tall with it. You want 1" - 1-1/2" gap between the…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

What Grade of Bolt is Required for Installing Timbren Spacer on Timbren Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching