Replacement Spacer Block For Trailer Hitch On 2000 Honda CR-V

Question

Question:

I have a hidden hitch for a 2000 crv and have lost one of the mounting washers. It is square and it accepts a carriage bolt. Can I buy one?

asked by: Dyrk

0

Expert Reply:

The spacer block you can order is part # RP3022.

This block measures 1/4 inch thick and is 1-inch wide and 3-inches long.

Trailer Hitch Hardware is designed for a one-time use only and if the hitch is being re-installed I recommend replacing all of the hardware for installation. For the kit you would need part # RHK. Then put your hitch number in the box and from the drop-down menu select the hitch manufacturer. The complete hitch installation kit will be sent to you.

expert reply by: Jeffrey L

0

Answer 1

When in the through bumper position, from the bottom of the frame to the bottom of the cross tube it looks to be approximately 8-1/2 inches. I have included a link to the installation instructions for you to view. Through bumper configuration…

view full answer...

Answer 2

If you are talking about Curt hitch #31302, the instructions do not mention drilling at all. And the first step says that models with tow hooks must remove the factory bolt from the underside of the frame at the forward attachment point. I have…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The primary difference is a matter of numbers. When installed, the Draw-Tite Class III #76025 will sit so the inside top edge of the receiver tube sits about 13 inches above the ground, and the receiver tube will sit under the bumper so that the…

view full answer...

Answer 10

I do have an option for you but I cannot advise you combine two hitch adapters together like the Roadmaster Hitch Extender part #RM-071 and the Roadmaster Dual Hitch Receiver Adapter part #RM-077-4 as this would be very unsafe. However, if you need…

view full answer...

Answer 11

Yakima does not recommend backing their Rack and Roll trailers like the #Y08107 you mentioned into water as the bearings aren't sealed and neither are the electrical connections. Your best option would be to back it right up to the waters edge…

view full answer...

Answer 12

The Yakima EXO Swing Away Enclosed Cargo Carrier for 2" Trailer Hitch #Y62VR may or may not cover your tail lights and license plate. If it does, you can add the License Plate and Tail Light Relocation Kit for Yakima EXO System #Y74VR This kit…

view full answer...

Replacement Spacer Block For Trailer Hitch On 2000 Honda CR-V

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching