Fitment and Compatibility of Replacement TruXedo TruXport Soft Roll-Up Tonneau Cover # TX278101

Question

Question:

I currently have the TruxPort TX278101-CVR replacement cover in my cart. I just want to verify that this is for the 6.5 foot bed before I purchase. Thank you.

asked by: Larry G

0

Expert Reply:

Without knowing more details of your vehicle, I cannot confirm this is correct for you but I can tell you that the # TX278101-CVR is the replacement cover that fits the following 6-1/2 foot bed vehicles. If your vehicle is in this group then this is the right replacement cover for your TruXedo TruXport Soft Roll-Up Tonneau original part number # TX278101.

2004 - 2007 Ford F-150 6-1/2 Foot Bed, excluding Stepside
2007 - 2008 Lincoln Mark LT 6-1/2 Foot Bed, with Trac System
2008 - 2008 Ford F-150 6-1/2 Foot Bed, without Trac System
2007 - 2008 Lincoln Mark LT 6-1/2 Foot Bed, without Trac System

I have linked all the above products to this page for your viewing and purchasing convenience.

expert reply by: Jackie C

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 12

If you are just looking for a new converter, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers part #PD4635V will be a direct upgrade for the Magnetek Converter Series 6300 Model 6332 that you have now.

view full answer...