Are there Locking Pins Keyed Alike for the Pro Series Adjustable Ball Mount 63070

Question

Question:

Do you Cary locking pins that would fit this hitch? Maybe a three pack? Keyed alike. Thank you

asked by: Anthony

0

Expert Reply:

There is a lock set designed specifically for the Pro Series adjustable ball mount # 63070. It is lock set # 63069. This set includes a 3/4" lock to replace the pin that holds the ball mount platform in place on the shank, and a 5/8" lock to secure the ball mount in a 2" hitch. There isn't a lock for the smaller pin used to secure the tri-ball part to the rest of the ball mount.

expert reply by: Michael H

0

Answer 1

The keys that come with the Draw-Tite Lock Set #63069 are keyed alike but if you are wanting to get more than one set and have them keyed alike you will need to use a different locking hitch pin. I recommend using the DeadBolt Trailer Hitch Receiver…

view full answer...

Answer 2

In regards to the B&W Tow & Stow 3-Ball Mount part #BWTS10047B, so long as you have the hitch balls pointed down there should be no issues stowing the ball platform under the receiver tube. I suppose there could be some odd setups that…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...