Replacement Claw Tightener for Yakima RailGrab Roof Rack Towers

Question

Question:

Looking for the black socket head cap screw called claw tightener which is about 1/4inch fine thread and approx. 3 1/2inch long. What is the part number and where can I purchase. Nothing available in hardware stores. For Yakima Railgrab tower.

asked by: Mike Y

0

Expert Reply:

It sounds like you are describing the screw that comes with the Replacement Wedge Assembly # Y8880150. The screw only comes with this kit. The only other possibility is # Y8880148 which are the adjustment knobs for RailGrab towers.

expert reply by: Michael H

0

Answer 1

It sounds like you are looking for the Replacement Adjustment Knobs for Railgrab part #Y8880148.

view full answer...

Answer 2

We do carry replacement parts for the Yakima Railgrab foot. For the claw base and nut you would want the part #Y8880279. The medium claws are no longer available. For the claws with pin adapters you would want the part #Y8880201. For replacement…

view full answer...

Answer 3

On the Replacement Upper Claw Base with Brass Nut for Yakima RailGrab Roof Rack Towers - Qty 1 #Y8880279, the brass nut will go into a slot on the top of that assembly. I reached out to my contact at Yakima to confirm. I've attached a photo to…

view full answer...

Answer 4

We have the replacement screw you are looking for with the part #Y8880150 which matches up to the nut of the #Y8880279 which is M6.

view full answer...

Answer 5

The discontinued Y8880205 does not include the bolt but the #Y8880150 which is the matching wedge assembly does include it.

view full answer...

Answer 6

I recommend using the Rhino-Rack Fairing for Roof Racks - 44" Long #RRRF3. When looking for a fairing, you want to cover as much of the bar as possible while able to attach within the feet/towers of your roof rack. The more air that you can…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Replacement Claw Tightener for Yakima RailGrab Roof Rack Towers

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching