Replacement Rail Grab Adjustment Screw for Tightening Claws to Side Rails

Question

Question:

I need to find a replacement for the claw base tightener screw which should be black in color. I cannot find this replacement on your site. Is this part offered or should I try a hardware store. I actually need to replace all the internal parts since they were lost or misplaced after storage and this part was the only one I couldnt find.

asked by: Tae

0

Expert Reply:

It sounds like you are looking for the Replacement Adjustment Knobs for Railgrab part # Y8880148.

expert reply by: Jameson C

0

Answer 1

It sounds like you are describing the screw that comes with the Replacement Wedge Assembly #Y8880150. The screw only comes with this kit. The only other possibility is #Y8880148 which are the adjustment knobs for RailGrab towers.

view full answer...

Answer 2

On the Replacement Upper Claw Base with Brass Nut for Yakima RailGrab Roof Rack Towers - Qty 1 #Y8880279, the brass nut will go into a slot on the top of that assembly. I reached out to my contact at Yakima to confirm. I've attached a photo to…

view full answer...

Answer 3

The discontinued Y8880205 does not include the bolt but the #Y8880150 which is the matching wedge assembly does include it.

view full answer...

Answer 4

The Yakima Railgrab will Medium Claws for Yakima RailGrab Roof Rack Towers - Qty 2 #Y8880205 are what I believe are the correct fit for your 2018 VW Tiguan. I've attached a photo that shows the first three styles being the smaller fit, the next…

view full answer...

Answer 5

Choosing the correct claws for your 2014 Volvo XC70, will depend on the height of your factory rails. -If your rail height is less than 1-1/16" (27 mm), you can use the Replacement Small Claw Assembly for Yakima RailGrab Roof Rack Towers…

view full answer...

Answer 6

We do carry replacement parts for the Yakima Railgrab foot. For the claw base and nut you would want the part #Y8880279. The medium claws are no longer available. For the claws with pin adapters you would want the part #Y8880201. For replacement…

view full answer...

Answer 7

I recommend using the Rhino-Rack Fairing for Roof Racks - 44" Long #RRRF3. When looking for a fairing, you want to cover as much of the bar as possible while able to attach within the feet/towers of your roof rack. The more air that you can…

view full answer...

Answer 8

We have the replacement screw you are looking for with the part #Y8880150 which matches up to the nut of the #Y8880279 which is M6.

view full answer...

Answer 9

If the crossbars on your 2014 Audi Q5 can be adjusted to being 25-7/8", 27-7/8", or 29-7/8" apart and are less than 4 inches in width the Sportrack Vista XL #SR7018 that you referenced would fit your 2014 Audi Q5. We don't have a…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...