Will Rhino Rack Roof Rack RRRVP27 Fit a 2012 Jeep Grand Cherokee with Chrome Roof Rails

Question

Question:

Hi is this the correct rack for a jeep grand cherokee i have included a picture of what is currently on my jeep thank you for your help!

asked by: Nicole

0

Expert Reply:

Thank you for the picture. Because you have the chrome center section on the roof rails of your 2012 Jeep Grand Cherokee that means you have the E Group package and the Rhino Rack roof rack part # RRRVP27 is the correct fit.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For your 2018 Honda HR-V to be compatible with the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs #TH898, you have to use slightly longer crossbars. The Hullavator requires 4-8 inches overhang to give clearance. In order to give…

view full answer...

Answer 2

When looking at the roof side rails on your 2019 Jeep Grand Cherokee you can determine if it has the E-Group package by inspecting them to see if there is a chrome section that runs down the middle of the rail. This chrome section indicates that the…

view full answer...

Answer 3

Yes, the Thule Motion cargo boxes, such as #TH629706, will fit on the Rhino-Rack roof rack crossbars, #RRRVP27. These Rhino-Rack bars are the same width and only 1/8 inch taller than the Thule AeroBlade bars which the Sonics also fit.

view full answer...

Answer 4

If you are using the Rhino-Rack Aero Bar Crossbars like #RRVA137B they have a dimension of 54" long x 3-1/8" wide x 1-3/16" tall which works for Thule boxes that use the PowerClick quick-release clamps, including the Thule Vector…

view full answer...

Answer 5

We have just what you are looking for from a roof rack for your 2020 Jeep Grand Cherokee that has flush black rails with a chrome center section with the Rhino Rack RVP Roof Rack #RRRVP27. This gives you aero shaped bars that sit flush with the feet…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...