What Is The Offset of Dutton-Lainson Replacement Handle Part DL70326

Question

Question:

How much offset ?

asked by: Bob Z

0

Expert Reply:

I walked out to our warehouse and pulled the Winch Replacement Handle by Dutton-Lainson, part # DL70326. I measured the offset from the inside of the metal and it measured 2 inches offset, from the very outside edge of the black handle I measured 6-1/4 inches offset.

expert reply by: Reno H

0

Answer 1

There are a couple of handles that you can use for your Fulton T1801 winch. For a 9 inch long handle use #F501109. For an 11 inch handle use #F501101. The longer the handle the easier it is to crank but it's easier to crank a shorter handle…

view full answer...

Answer 2

The hole in the handle is slotted, and is meant to replace the handle on a Dutton-Lainson DL1400 or DL1402 winch. The proper replacement for your Fulton T1801 winch would be the Fulton Replacement Winch Handle, part #F501109 or #F501110 depending…

view full answer...

Answer 3

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side.…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 6

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 11

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 12

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

What Is The Offset of Dutton-Lainson Replacement Handle Part DL70326

Product Page this Question was Asked From

Continue Researching