Installing 6-Way Trailer Connector in Bed of 2006 Chevy Silverado 2500

Question

Question:

I have a 2006 Chevrolet 2500 pickup and am wanting to install a 6 pole round plug in my box. I am wondering what the easiest way is to do this. Thanks

asked by: Ryan P

0

Expert Reply:

The easiest way to provide a 6-way connector in your truck bed would be to use the Curt 5th Wheel and Gooseneck Wiring Harness # C56000 along with a 7 to 6-way adapter like part # 47549.

One end of the harness has two connectors. If your Silverado has an existing 7-way connector, unplug the harness behind it, and plug the harness inline.

I will include links to the harness and adapter below.

expert reply by: Mike L

0

Answer 1

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 2

You can certainly add a 7-way trailer connector to your trailer with 6 wires. You would simply have 1 pin on the 7-way connector that did not function. I recommend adding a 7-way molded trailer wire connector like part #H20046, and a junction box…

view full answer...

Answer 3

Assuming that the 7-way on the bumper is from the factory and the tow package harness can be unplugged from the rear of the connector, using a T-connector like #41157 is what I'd recommend. Simply temporarily unplug the connection at the rear of…

view full answer...

Answer 4

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...