What is the Overall Height of the CE Smith Bunk-Style Guide-Ons # CE27600

Question

Question:

want to make sure of dimensions of height as they would have to mount on top of channel due to step from fender back to tail light so i still would have to drill for bolts but want make sure of height as so it wont be to high on boat

asked by: Jimmy H

1

Helpful Expert Reply:

The overall height of the CE Smith Bunk-Style Guide-Ons # CE27600 is right at 21 inches.

I also attached an install video for this kit for you to check out as well.

expert reply by: Jameson C

1

Answer 1

There isn't a set boat length require when using the CE Smith Bunk-Style Guide-Ons #CE27600. The bunks themselves are 60 inches long and will help you to keep the boat centered between them longer than post style guide-ons would. This is…

view full answer...

Answer 2

The mounting hardware that comes with the CE Smith Bunk-Style Guide-Ons for Boat Trailers #CE27600 will fit a 3 inch by 3 inch trailer frame. The guide ons can extend out up to 13 inches from the frame of the trailer they are installed on. There is…

view full answer...

Answer 3

Yes, the CE Smith Bunk-Style Guide-Ons for Boat Trailers - 60" Long - 1 Pair #CE27600 can work on the inside of a pontoon boat. Based on the photo you may prefer the CE Smith 90-Degree Bunk Board Guide-On Kit #CE27600K90 which will…

view full answer...

Answer 4

I am not sure I totally understand what you are asking but the CE Smith Bunk-Style Guide-Ons for Boat Trailers part #CE27600 comes with two 5' long bunk boards as well as the brackets needed to attach them. These bunk boards will only require…

view full answer...

Answer 5

I do have an option for you, but there is not a version of the CE Smith Bunk-Style Guide-Ons for Boat Trailers #CE27600 you were looking at that is any longer or designed for tandem axle trailers. Instead you will need to go with the CE Smith…

view full answer...

Answer 6

For bunk style guide-ons such as #CE27600 the bunk board and boat should only barely touch if at all. There isn't a hard and fast rule that says it should be this many inches. But since guide-ons are not meant to support weight like a…

view full answer...

Answer 7

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 12

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

What is the Overall Height of the CE Smith Bunk-Style Guide-Ons # CE27600

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching