Mounting Hole Spacing on Curt Front Mount Trailer Hitch Receiver 31514

Question

Question:

I was wondering if you had cads available for this product.

asked by: Chris S

0

Expert Reply:

We do not have CAD drawings for the Curt Front Mount Trailer Hitch Receiver # 31514 but I have linked the written installation instructions for you. I also went to our warehouse and measured the holes on the mounting flange in the hope that this information will be useful to you.

Please refer to the linked photo. The information shown on the photo is the same for both sides of the hitch. The horizontal mounting hole on the vertical tab measures 1/2-inch in diameter; it's center is 2-1/4-inches above the top of the mounting flange. The two oval slots on the flange each measure 1/2-inch x 1-inch. Their centers are 3-1/2-inches apart.

expert reply by: Adam R

0

click to enlarge

Answer 1

I checked with Curt and they told me that the overall width of the Curt front hitch #C31013 is 32.50 inches and the center to center hole dimension is 30 inches.

view full answer...

Answer 2

I went out the warehouse and took the measurements you asked about on the Curt Front Mount Hitch, part #31408. I've attached a diagram showing them. The inside distance between the mounting plates is about 27-1/2 inches. Between the 2 sets of…

view full answer...

Answer 3

The Curt Front Mount Trailer Hitch Receiver #31198 you saw is a confirmed fit for the 2008-2018 Toyota Land Cruiser, 2008-2021 Toyota Sequoia and 2007-2021 Toyota Tundra. This receiver has never been confirmed to fit on a Lexus LX470. It does appear…

view full answer...

Answer 4

I attached a picture that has the most relevant dimensions of the Curt #31408. The length of the main crosstube as well as the distance between the mounting holes. The vertical height would be just a little over 2-1/2 inches. Our hitch manufacturers…

view full answer...

Answer 5

There is a way to find where the end of the hitch receiver will sit once installed on your 2011 Toyota Tundra, but we have not had a chance to install the Curt Front Mount Hitch, #31198, on a 2011 Toyota Tundra yet, so I do not have a specific…

view full answer...

Answer 6

The Curt #33055 you mentioned isn't a fit for the 1991 F-250, it's a fit for the E-Series Vans, which Curt confirms. Unfortunately, they don't offer a front mounted hitch for your truck. The bolt hole spacing I was able to obtain is as…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Mounting Hole Spacing on Curt Front Mount Trailer Hitch Receiver 31514

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching