Where To Find Torque Specs for Curt Class V Trailer Hitch # C15323 for 2007 GMC Sierra New Body

Question

Question:

Hi i got a gmc 2007 sierra 1500 sle new body and i want to install 15323 CURT Trailer Hitch Receiver - Custom Fit - Class V Xtra Duty- 2. How many pounds lbs torque to tie the bolts?

asked by: Jaime G

0

Expert Reply:

The current torque specs are located in the instructions, in step 6. You can see the instructions by clicking the provided link. We don't publish the torque specs on the website because the hitch manufacturer can change them

If you click the provided link, you can see the hitch being installed on a 2007 GMC Sierra New Body.

expert reply by: Mike L

0

click to enlarge

Answer 1

I went out to the warehouse and took some measurements for the Curt Trailer Hitch Receiver item #13028 you referenced. The measurement running from the middle of the bolt holes across the length of the receiver is 31-1/8". I can confirm that…

view full answer...

Answer 2

The distance between the mounting holes of the #e98849 from left to right is 35-5/8 inches.

view full answer...

Answer 3

It is, I went and measured the distance from the mounting flanges of a Curt Hitch part #C15703 to the cross tube that we have in stock and found that it measures right at 6 inches. I attached an install video for you to check out as well.

view full answer...

Answer 4

I went to the warehouse and measured the Curt Trailer Hitch Receiver, part #C15703. I have attached a photo of the trailer hitch and have noted the dimensions you can check out. This is a Class V trailer hitch and it has a 2-1/2 inch receiver…

view full answer...

Answer 5

Yes, the Curt Trailer Hitch Receiver #C15323 will fit on your 2005 Chevrolet Silverado 1500. This receiver is designed to fit the standard factory bumper but does not screw into the bottom of the bumper.

view full answer...

Answer 6

In regards to the Curt Trailer Hitch Receiver part #C15302 which is a fit for a 2001 Chevrolet Silverado 2500 HD - 6-1/2 Foot Bed, there are only two factory weld nuts in the frame which get reused, they are the two closest to the bumper. The other…

view full answer...

Answer 7

I had our warehouse measure the Curt Trailer Hitch Receiver #C15703 you were looking at, and has an overall width of 40-5/8", overall length of 29". The distance between the vertical mounting holes is 14-1/2" center to center, and the…

view full answer...

Answer 8

I have added a cut out of the installation instructions, which are linked on this page and also linked on the product page of the Curt Trailer Hitch #C15810 that fits your 2006 Ford F-250. You can refer this cut out or you click either link to the…

view full answer...

Answer 9

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Where To Find Torque Specs for Curt Class V Trailer Hitch # C15323 for 2007 GMC Sierra New Body

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching