Where to Find Stoplight Switch on 2007 Jeep Liberty for Brake Controller Install

Question

Question:

Things went great with the brake controller install except the part about the brake stop light switch. It said it was over the brake pedal but I cant find it. I have a 2007 Jeep Liberty.

asked by: Donna W

0

Expert Reply:

On your 2007 Jeep Liberty, If you are referring to the red wire on the brake controller, it attaches to the wire on the stoplight switch that carries a signal only when the brake pedal is pressed. You will need a circuit tester, like # PTW2993, to find this wire. Most likely it's going to be a white wire with a green or tan tracer. See attached install video.

Normally you can pretty easily test the wires on the pedal to figure out the correct one. Sometimes you end up having to use the third brake light circuit.

expert reply by: Jameson C

0

Answer 1

It sounds like the problem you are having is related to one of the possibilities you have mentioned. It is nearly impossible to press a race in straight at home unless you have the proper equipment and have done it before. Taking the drums to a…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Where to Find Stoplight Switch on 2007 Jeep Liberty for Brake Controller Install

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching