Brake Controller Installed on 2013 Chevy Avalanche-Now Vehicle Won't Start

Question

Question:

So...I have the adapter cable 3016-P and the brake controller. I got the power junction cover off and there appears to be only one slot where the plug will fit. I put it in, attach the brake controller and the truck wont start. I assume Im doing something wrong somewhere... So heres a picture of the junction box. The plug I used is the bottom center. So...any suggestions on how I screwed up?

asked by: Steve

1

Helpful Expert Reply:

The brake controller wiring on a 2013 Chevy Avalanche is a bundle of 5 wires located under the dash between the brake and the emergency brake pedals. The wiring harness will have a white label wrapped around it, which should make it easier to locate. A plug in harness like the # 3016-P isn't needed on your Avalanche.

Your brake controller will wire directly to the bare ended wires in this harness, the wire colors will match up as follows:

Red/Black tow package wire connects to Black controller wire
White tow package wire to White brake controller wire
Light Blue/White tow package wire to Red brake controller wire
Dark Blue tow package wire to Blue brake controller wire

The orange wire isn't used.

I've linked you to an FAQ article that exactly describes how to install the brake controller. I hope you'll find it helpful.

expert reply by: Mike L

1

click to enlarge

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The Optronics light that you referenced, part #ST70RB, is an exact replacement for Bargman light #40-06-001. If you can find that part number on your Bargman light, then we can be sure that this light is the correct replacement. Even if your Bargman…

view full answer...

Answer 3

We can get you a replacement for your TDE LP75 disc brake actuator; that's a 7,500 lb actuator that accepts a 2" hitch ball, and the correct option will depend on if your trailer tongue is 3" wide x 4" tall or 3" wide x…

view full answer...

Answer 4

As far as the labeling of the Kodiak Disc Brake Kit - 13" Rotor - 8 on 6-1/2 - E-Coat - 9/16" Bolts - 8K Dexter Disc Kit #K2R89DDE, Dexter is the parent company of Kodiak. The reason this particular kit calls out Dexter is anything above 7k…

view full answer...

Answer 5

I'd be happy to help you with that. Since it's a tractor, there's likely a few differences from what would be seen on a standard passenger vehicle. You very likely won't need to contend with turn signals and taillilghts, and you…

view full answer...

Answer 6

It's pretty easy to determine the correct replacement leaf springs for your trailers, and there's different ways for double-eye springs and slipper springs. You do have to account for the sag, so go with ones that measure shorter than what…

view full answer...

Answer 7

Hi Robert, If you're just wanting to replace the condenser unit on the rooftop and retain use of your current air distribution box and thermostat then you'll just need to determine what style connector your current unit has. If you remove the…

view full answer...

Answer 8

On a 2019 Escalade, the plug you're looking for is in a junction box on the firewall to the left of the brake pedal. The junction box has a black cover, which will need to be removed and the #3016 harness you'd looked at will plug into the…

view full answer...

Answer 9

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...