What is Height Gain from Installing Dexter Trailer Springs Over-Under Conversion Kit K71-385-00

Question

Question:

The question was asked how high the kit raises the trailer, but the expert never answered the question. Talked on and on, but still never answered the question. How high?

asked by: Andrew W

1

Helpful Expert Reply:

When installing an over-under kit like Trailer Spring Conversion Kit # K71-385-00, the height gain will be close to the sum of the axle diameter plus the height of the spring stack. So for this kit which fits 3-inch axles, add the 3-inch axle diameter to the height of your leaf spring stack.

expert reply by: Adam R

1

Answer 1

The Double RV Waste Valves - Elbow - Rotating - 3" and 1.5" Hubs to 3" Lug #T80 will use the Valterra RV Sewer Spigot with Flange - 1-1/2" #T1005-1 to match the original hub. This secures to your pipe with solvent…

view full answer...

Answer 2

I have two options for you to raise your trailer and gain more clearance between the fender and tire. The most cost effective option would be to flip the axles with a Dexter Trailer Springs Over-Under Kit part #K71-384-00 or part #K71-385-00. That…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 8

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the jack…

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...