What Diameter Lunette Ring Works with Curt Pintle Hook for 2-Inch Hitches C48004

Question

Question:

Will this part work with a lunette eye of 3?

asked by: Donnie

0

Expert Reply:

The Curt Pintle Hook for 2-Inch Hitches # C48004 fits lunette rings with an inside diameter of at least 2-1/2-inches, so if yours is 3-inches inside diameter it will be compatible. This powder-coated forged steel pintle hook resists rust and offers a 20K capacity.

expert reply by: Adam R

0

Answer 1

Pintle hitches are made to fit certain sized Lunette rings. The rings that we carry are only available in 2-1/2" or 3" diameter sizes. For example, the Curt Pintle Hook for 2" Hitches #C48004 fits lunette ring couplers with a minimum…

view full answer...

Answer 2

Definitely! The measurement of the circular area when the hook is completely closed on the #C48004 is 2.03" across. As far as the distance between the narrowest point of the top and lower of the opening when the hook is open, that measurement is…

view full answer...

Answer 3

The Curt Pintle Hook for 2" Hitches - 20,000 lbs, #C48004 will be at its full capacity for a 10 ton trailer, but is rated to handle it. Your 2010 Ram 3500 HD is only rated to tow 12,100 at the bumper unless you have done extensive upgrades in…

view full answer...

Answer 4

Tongue weight isn't considered as much of a factor for pintle hooks because there isn't as much downward force onto the hitch like there is with a standard coupler. With that being said a pintle hook's tongue weight is considered to be…

view full answer...

Answer 5

The outer eye diameter of the Buyers Products 10-Ton Lunette Ring w/ 3" I.D. #337B16140 is 6-1/4". The mounting holes for the 5/8" hardware is space 2" on center. I have included an image with these measurements.

view full answer...

Answer 6

For a 20k lunette ring we have the part #337B16140 for just the ring or part #337B20143 for a ring and a channel.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...