Will Clamps of B&W Biker Bar Motorcycle Tie-Down System # BWMC2301 Stay Tight While Traveling

Question

Question:

The clamp on the frameof the bike,will it loosen as you tow trailer? Looks like it could unscrew with vibration.

asked by: Allen L

0

Expert Reply:

The clamps of the B&W Biker Bar Motorcycle Tie-Down System for Trailers # BWMC2301 that you referenced are not going to come loose from vibration as you travel. If that were a problem we would have heard about it by now.

expert reply by: Jameson C

0

Answer 1

The 3/4" plywood floor will be thick enough to install the B&W Biker Bar Motorcycle Tie-Down System #BWMC2301 and use with your Harley Touring. If you take a look at the accompanying cutout of the directions I added, it states "The…

view full answer...

Answer 2

The waste valve you came from, part #T58 is not a valve that uses glue because it is designed to attach to the RV side and the waste tube with the bayonet adapters on each side of the valve. We do have waste valves that do require gluing. I have…

view full answer...

Answer 3

Yes, you can use an offset toilet flange like the one you mentioned with the Dometic toilet you asked about: - Dometic Full-Timer RV Toilet - Standard Height - Elongated Bowl - White Ceramic #DOM87FR I have added a link below to a video review and…

view full answer...

Answer 4

You can just use a replacement flange like the LaSalle Bristol Toilet Floor Flange for RV #344633633. You'll have to cut out the only flange and will most likely need to add a bit more straight pipe to glue into the hub of this flange. If…

view full answer...

Answer 5

For your 2022 Chevrolet Silverado 2500HD with the Multi-Flex tailgate B&W has a line of hitches that were specifically designed for your tail gate in mind. B&W Tow & Stow 2-Ball Mount #BWTS20066BMP B&W Tow & Stow 2-Ball Mount…

view full answer...

Answer 6

I can absolutely help you as there are a lot of standalone options, but we do have exactly what you are looking for, which are the following: - Curt Rebellion XD Shock Absorbing Adjustable Ball Mount with 2" and 2-5/16" Balls #C57UR - Lock…

view full answer...

Answer 7

Yes, both the Standard Lock Set #C78CR and the InfiniteRule Lock Set for Curt Rebellion XD Ball Mount #IR47FR that's designed around the Rebellion XD #C83WR will also work with the Curt Adjustable 2-Ball Mount #C79NR.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The Curt Rebellion XD Shock Absorbing Adjustable Ball Mount #C57UR is the only one currently in production that fits a 2-1/2" receiver. It has a 2" and 2-5/16" ball mount that can be flipped depending on your application. The hitch is…

view full answer...

Answer 10

Replacement toilet floor flanges are universal so it will work, but you can determine the correct one based on the threading of your current flange. They will work with 3" pipes which you need to have as well. - Male Thread: Replacement RV…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...