Which Trailer Connector for 2015 Ford Transit T250

Question

Question:

2015 Ford Transit 250 without towing package. Installing trailer hitch and wiring. Which trailer wiring kit do I need? Thanks.

asked by: Rod

0

Expert Reply:

I'd recommend the Curt 4-pole trailer wiring harness, part # C56327. This is a confirmed fit for your 2015 Transit T250.

I've linked to an install video that you might find helpful.

expert reply by: Mike L

0

Answer 1

On your 2016 Ford Transit T350 it sounds like you have the hardwired 7-way and a damaged brake controller. My recommendation is to replace your wiring with the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56327 and…

view full answer...

Answer 2

If your trailer is equipped with a 7-Way but you only need to power its basic signal lights (and not electric brakes) then adding a 7-Way connector to your 2020 Ford Transit T250 will actually be fairly simple. To do this you will need to start with…

view full answer...

Answer 3

For a brake controller for your 2020 Ford Transit T250 I would recommend the Prodigy P3 Brake Controller part #90195. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake…

view full answer...

Answer 4

We have just what you need to get this job taken care of. There are two wiring kits you will need, the Curt T-Connector #C56327 and the Universal Installation Kit #ETBC7. These two kits combined will include everything you need to install a 7-way on…

view full answer...

Answer 5

It is a 7.5 amp fuse which goes into the fuse box in the side kick panel. I will include a link to the web page with the instructions, and the installation video for your reference below.

view full answer...

Answer 6

Not to confusing at all. There are a lot of wires to keep straight, but once you do it, you will be surprised at how easy it was. I will go through a quick run down of how to wire up the ETBC7, then how to wire up the Brake Controller. I will also…

view full answer...

Answer 7

You will need to install a Brake Controller in your RV to actuate the brakes on your trailer. In addition to the Controller, you will also need the 7-Way Installation Kit #ETBC7. The existing 4-Way connector on your RV would plug into the 7-Way…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...