Trailer Hub with 6 on 5-1/2 Bolt Pattern for #84 Spindles that Uses L44649/L68149 Bearings

Question

Question:

Can anyone help me find a hub that will fit this spindle with 6 on 5 - 1/2 bolt pattern?

asked by: Chan

0

Expert Reply:

We have many hubs and hub and drum assemblies that will fit spindle # TRU47FR and that have a 6 on 5-1/2 bolt pattern. If you just want an idler hub then I recommend etrailer hub # AKIHUB-655-35-K. this hub comes with the races, bearings, seal, dust cap, and lug nuts.

For a hub and drum assembly I recommend # AKHD-655-35-K. The races, bearings, seal, cap, and nuts are included with this assembly as well.

The etrailer parts are a fantastic value with high quality and good price compared to other brands.

expert reply by: Michael H

0

Answer 1

Yes, it is possible. You will need to use a hub and drum assembly that works with the 3,500-lb axle on your 2015 Jayco Jay Flight SLX 195RB Travel Trailer. To get the right fit, you need to match up everything to your bearings sizes which are stamped…

view full answer...

Answer 2

When fitting wheels to a Dexter Trailer Hub Assembly, #8-213-5UC1, you would need to measure the wheels you are trying to use. You would measure the bolt pattern, the center hole diameter, and the stud size. To measure the bolt circle on a 6 lug…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 7

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 8

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 9

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Trailer Hub with 6 on 5-1/2 Bolt Pattern for #84 Spindles that Uses L44649/L68149 Bearings

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching