Will Powerbuilt 1-7/8 Inch 12pt Socket Work with Equal-I-zer Weight Distribution System

Question

Question:

Will this socket work to install the ball on an Equalizer hitch head? I know it needs to be a thin walled socket.

asked by: Ron H

0

Expert Reply:

The Powerbuilt 1-7/8 Inch 12pt Socket # ALL643216 that you referenced will fit in the Equal-I-zer weight distribution hitch, like # EQ37120ET, # EQ37140ET, # EQ37040ET, # EQ37060ET and # EQ37100ET, to torque down the hitch ball.

In the review video on the # ALL643216 socket, we found we were able to torque down the hitch ball in the Equal-I-zer hitch just fine with the socket.

I have attached the review video of this socket for you.

expert reply by: Victoria B

0

Answer 1

You could certainly reverse the position of the lamps by installing the #328-003-81LBM1 lamp on the passenger side and the #328-003-81BM1 lamp on the driver's side. Both lamps wire the same way, the white wire is the ground connection, the red is…

view full answer...

Answer 2

We had a customer who was able to replace his Dexter 8-155 hubs with the #8-201-5UC3-EZ that you referenced so they should work well for you. You can verify that this hub will work for you by pulling your current hub and making sure they have inner…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

Yes, there is a hitch that fits your 2023 Mercedes GLE 350. That hitch is the Stealth Hitches Hidden Rack Receiver #SH99MR. This hitch has a removable receiver for a completely hidden design when not in use. This version of the hitch has a max tongue…

view full answer...

Answer 6

Yes the Replacement Brass Connector #T4750300 for Titan Disc Brake Actuators will fit a Tie Down 660e disc brake actuator.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

We have the bearing part #387A which is over 2 inches in inner diameter and is seen on 10,000 lb axles but I'd have to know exactly what your spindle dimensions are to know for sure what you'd need. If you can use a digital caliper like the…

view full answer...

Answer 10

For your 2020 Mercedes Benz GLE 350 SUV we have the Stealth hitch part #SH24GR which is a confirmed fit and actually comes with trailer wiring as well.

view full answer...

Answer 11

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...