Will Curt Hitch for Ford C-Max Affect Hands Free Liftgate Operation

Question

Question:

2016 Ford C-Max Curt Trailer Hitch Receiver Class II - 1-1/4 Is this hitch compatable with the Ford C-Max hands free lift gate? The Draw Tite indicates that their unit is, but I like the heavier capacity Curt. The intent is to carry a Titus double bike rack. Thank you

asked by: Perry H

0

Expert Reply:

It is possible that Curt trailer hitch # C12092 will block the sensor for the hands-free liftgate on the 2016 Ford C-Max. In some cases, it will just limit the coverage area of the sensor. Ford must angle that sensor differently amongst vehicles because some people seem to have trouble and others do not.

At worst you would just have to kick your foot on either side of the hitch instead of in the middle.

Curt requires the use of their stabilizer strap part # 18050 when using their hitch to carry a non-supported load like a bike rack. I attached a review video for you to check for the strap as well. Because of this you may rather have the EcoHitch Hidden Trailer Hitch Receiver # 306-X7200 that does not have the same requirement and has a 2" receiver opening.

expert reply by: Jameson C

0

Answer 1

The trailer hitch you will need to use to carry three bikes on a 2013 Ford C-Max is the 1-1/4" Curt Trailer Hitch Receiver part #C12092 because of the class II rating and 350lb tongue weight rating or the EcoHitch Hidden Trailer Hitch…

view full answer...

Answer 2

I have attached a link to the installation instructions for the Curt Trailer Hitch Receiver #C12092 along with an installation video. Installation requires the exhaust system to be temporarily lowered and some access holes will need to be enlarged…

view full answer...

Answer 3

Drilling holes into your vehicle frame to install a trailer hitch is not uncommon at all. As long as you have the proper tools installing the Curt Trailer Hitch, part #C12092, on your 2016 Ford C-Max is a fairly easy install that is estimated at…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 8

Because the 8-14.5 tire that you've got sits on a 14.5" wheel, so you wouldn't be able to switch tire sizes with anything that we have available without also switching to a new wheel as well. If you've got a 6 on…

view full answer...

Answer 9

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack…

view full answer...

Answer 10

The Grease Seal part #168233 has a double lip so it can be used on a boat trailer and be submersed under water, yes. This is also the correct replacement for the NOK AD2527E Grease Seal that you have now.

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...