Could the Equal-i-zer Weight Distribution EQ37121ET Fit an EAZ Lift Shank

Question

Question:

Hi, can I use an EAZ-LIFT shank on an Equalizer part # EQ37121ET

asked by: Brian

0

Expert Reply:

The Equalizer # EQ37121ET that you referenced has 3/4 inch holes that are spaced 1-1/4 inches apart. If the shank of your Eaz system is compatible with that this the WD system would work well for you. Nearly all WD system use the same hole dimensions. We have found that almost all brands can use each others shanks.

expert reply by: Jameson C

0

Answer 1

The Andersen Camper Wheel Chock and Leveler #AM3604 will work great for your your tandem axle trailer as long as the trailer doesn't weigh over 30,000 pounds. The chocks can be used on tires that are up to 32 inches in diameter and your…

view full answer...

Answer 2

The spring bars of weight distribution systems are designed to install and hang parallel with the frame rails on an A-frame trailer. They will hang almost completely under the frame rails, so the turning radius of a truck will only be slightly…

view full answer...

Answer 3

The Andersen Camper Leveler #AM3604, which is sold as a set of one leveler and one chock, will work on your tandem axle trailer even if the gap between the tires is only 2-1/2-inches. If you refer to the linked video and photo you'll see that the…

view full answer...

Answer 4

Yes, the narrow end of the Andersen Camper Wheel Chock and Leveler part #AM3604 can be trimmed up to 4 inches to allow for narrow tire spacing on trailers. I have attached a couple of diagrams for your reference. Anderson recommends cutting down the…

view full answer...

Answer 5

Yes, the Equal-i-zer is significantly better than the Fastway e2 because the Equal-i-zer has four points of sway control and the Fastway e2 only has two points of sway control so there will be a much greater reduction in trailer sway. This will be…

view full answer...

Answer 6

For starters, if the gross combined weight rating (GCWR) is 16,200 lbs and the gross vehicle weight rating (GVWR) is 7,000 lbs then your towing capacity is 9,200 lbs, not 10,800 lbs. The correct GCWR and GVWR figures will be found on the driver's…

view full answer...

Answer 7

When installing a weight distribution system on a new vehicle you will want to basically run through the entire setup procedure so that you can make sure you have the correct amount of spring bar tension in the system. The goal with an Equalizer…

view full answer...

Answer 8

I contacted Equal-i-zer and the most common reason that the weight distribution head from the Equal-i-zer Weight Distribution systems like part #EQ37120ET would pull away from the shank is the angle set bolt on the bottom of the head is too tight…

view full answer...

Answer 9

For a travel trailer with an 8,600 lb GVWR, your loaded total tongue weight will be somewhere in the 1,000 lb range, and that's the number we'll use to get the right weight distribution system. The ideal system would be one in which your…

view full answer...

Answer 10

Most likely you are going to need the higher rated system part #FA92-00-1200 since by the time you load up the trailer it will have a tongue weight of higher than 1,000 lbs. Also, you have to consider the weight of any cargo behind the rear axle of…

view full answer...

Answer 11

There were two different style cameras that came in the WVOS511 kit, which has since been discontinued. Each of the cameras had different antennas. One is straight on the newer model camera and the one has an elbow type on the older camera. An easy…

view full answer...

Answer 12

From what I was able to find on your Voyager WV0S511 (discontinued) there were two different style of cameras that were used. One of which used a straight antenna like the Replacement Wireless Antenna for Voyager Backup Camera System #PXXHD0006301R…

view full answer...