Weight Distribution Head Pulls Away From Shank When Setting Up Equal-i-zer 12K System
Question:
I torque the bolts down, but the shank head keeps pulling back from the shank. When i look it seems that the flat washer and lock washer are out of thread. But why is this pulling away?
asked by: Tommy J
Helpful Expert Reply:
I contacted Equal-i-zer and the most common reason that the weight distribution head from the Equal-i-zer Weight Distribution systems like part # EQ37120ET would pull away from the shank is the angle set bolt on the bottom of the head is too tight when you torque the bolts. If it is too tight when you try to torque the bolts the head will pull away from the shank. You want to angle set bolt to be barely snug before you torque the bolts. The angle set bolt needs to be last bolt that is tightened when you set up the system. The number 19 bolt on the diagram I have attached is the angle set bolt.
You also want to make sure you are using the proper amount of spacers for your setup. I have also attached a help video for your reference.
Product Page this Question was Asked From
Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 12,000 lbs GTW, 1,200 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Some Sway
- Includes Shank
- Electric Brake Compatible
- Surge Brake Compatible
- Fits 2 Inch Hitch
- Allows Backing Up
- 1000 lbs
- 1100 lbs
- Equal-i-zer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 12,000 lbs GTW, 1,200 lbs TW
- Shop: Curt Wall Mount for 2" Hitch Accessories - 350 lbs
- Shop: B&W Continuum Weight Distribution System w/ Sway Control for 2" Hitch - 16K GTW, 1.6K TW
- Q&A: How to Gain Clearance for Turns Using Equal-i-zer Weight Distribution System
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Search Results: equalizer hitch
- Search Results: weigh safe
- Shop: Equal-i-zer Weight Dist Shank - 12" Long - 10" Rise, 6" Drop - 600 to 1,400 lbs TW
- Shop: VESA Adapter Plates for MORryde RV TV Mounts - 200mm x 100mm or 200mm x 200mm
- Search Results: trailer hitch
- Video: Best 2023 Kia Telluride Trailer Hitch Options
- Q&A: Recommended Weight Distribution System For 7,600-lb Travel Trailer
- Shop: Bug Shield
- Shop: WeatherTech Hood Protector
- Search Results: equalizer shanks
- Video: etrailer Class III Trailer Hitch Installation - 2023 Kia Telluride
- Shop: RV Camera
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Q&A: Can You Switch Between 10K and 12K Equal-i-zer Weight Distribution Systems
- Q&A: Adjusting Small Trailer Pitch Difference with Equal-i-zer Weight Distribution System Installed
- Q&A: Shank Recommendation for Equal-i-Zer Weight Distribution for Additional Drop
- Q&A: Weight Distribution System Recommendation for Trailer that Weighs 7,600 lb
- Q&A: Solution for Bucking When Towing with Equal-i-zer Weight Distribution System
- Video: Equal-i-zer Weight Distribution System with 4 Point Sway Control Review
- Video: Camco RV Refrigerator Braces Review
- Search Results: anderson leveler
- Video: Review of Voyager RV Camera System - Prewired Backup Camera - ASA24YR
- Shop: Brake Controller
- Video: Equal-i-zer Weight Distribution - WD With Sway Control - EQ37120ET Review