How to Mount a Fulton Plastic Trailer Fender to a Trailer

Question

Question:

How is this fender mounted? What are the mounting surfaces? Can it be mounted by bolting the skirt to the frame? Or must it be mounted by a bracket screwed to the bottom of the fender on the outer vertical surface?

asked by: Dave

0

Expert Reply:

You can use the hardware and mounting brackets from your original fenders, or I recommend L-shaped brackets, like part # PF775-BKT-2, to mount the fender to your trailers frame. I have attached a link to our product page of mounting brackets we have for trailer fenders.

I recommend the L brackets. The one end would be up underneath and the other end would attach to the trailer frame through that skirt. I will include a picture that should better illustrate this.

expert reply by: Michael H

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 7

I am sorry I don't have any tires that are going to fit your rim. I do have a couple of comparable size tires that come in a wheel tire combo. I have listed the two below along with their lug patterns. 5 on 4-1/2 Lug Pattern - Kenda 205/65-10…

view full answer...

Answer 8

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

How to Mount a Fulton Plastic Trailer Fender to a Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching