Side Mount Trailer Jack Recommendation for a 4,000 lb Boat Trailer

Question

Question:

Hello, Is there a heavier duty version then this jack? Looking for side mount for a 4000 pound 21 foot boat on a dual axle trailer.

asked by: Duane

0

Expert Reply:

Actually the part # DL22457 that you referenced should work just fine for you. This jack has a lifting capacity of 1,000 lbs which would be more than enough for a setup that has a 4,000 lb boat. Most likely your tongue weight would be around 500 or 600 lbs so this jack would work just fine.

I attached an install video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs #FTJ120W0301 will be able to utilize the Atwood welded snap ring mount.

view full answer...

Answer 2

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

I really wish we had replacement parts still for the Atwood couplers but since they've been out of business for so long we don't have any way to get the parts you are wanting.

view full answer...

Answer 8

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 9

The serial number and VIN are typically printed on a label or plate placed somewhere on the trailer's pole tongue, although it could possibly found elsewhere on the trailer frame, possibly on the inside edge of the frame so it's more…

view full answer...

Answer 10

The Rear Hanger for 2-1/2" Wide Slipper Springs - 6" Tall #093026 you were looking at has a hole just to allow you to measure the height of the hanger, and the hole lines up with the bottom of the support that the hanger rests against. To…

view full answer...

Answer 11

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Side Mount Trailer Jack Recommendation for a 4,000 lb Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching