What Does Hole In Rear Hanger For 2-1/2" Wide Hanger Used For?
Question:
this hanger, why does it have a hole? and how do I measure my rear slipper spring hanger with NO HOLE, it does have the 5/16inch bolt. Thanks, I have more questions so dont try leaving early.
asked by: Dave H
Helpful Expert Reply:
The Rear Hanger for 2-1/2" Wide Slipper Springs - 6" Tall # 093026 you were looking at has a hole just to allow you to measure the height of the hanger, and the hole lines up with the bottom of the support that the hanger rests against.
To measure your hanger you will need to measure from the top of the hanger to the center of the 5/16" bolt hole you mentioned to get the length.
You will also need to measure the inside width of the hanger as slipper springs can be 1-3/4" - 3" wide. The # 093026 you were looking at is for 2-1/2" wide slipper springs and measures 6" tall.
Based on the picture of your slipper spring you will more than likely need the # 30-28 instead as it has the same 5/16" hole, but is 5-1/4" tall and 2" wide.
If you can confirm the size of your hanger I would be happy to confirm the correct replacement.
I included videos of the products mentioned for you to take a look at.
Products Referenced in This Question
Rear Hanger for 2" Wide Slipper Springs - 5-1/4" Tall - 5/16" Bolt Hole
- Trailer Suspension Parts
- Hangers
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Slipper Springs - 2 Inch
- 5/16 Inch Diameter
- 5-1/4 Inch Tall
- Single Axle
- Tandem Axle
- Triple Axle
- Redline
more information >
Product Page this Question was Asked From
Rear Hanger for 2-1/2" Wide Slipper Springs - 6" Tall
- Trailer Suspension Parts
- Hangers
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Slipper Springs - 2-1/2 Inch
- 6 Inch Tall
- Single Axle
- Tandem Axle
- Triple Axle
- Redline
more information >
Continue Researching
- Shop: Rear Hanger for 2" Wide Slipper Springs - 5-1/4" Tall - 5/16" Bolt Hole
- Shop: Rear Hanger for 2-1/2" Wide Slipper Springs - 6" Tall
- Shop: Tandem-Axle Trailer Hanger Kit for Double-Eye Springs - 2-1/2" Front/Rear, 4-1/2" Center
- Shop: Front Hanger for 2" Wide Slipper Springs - 4-1/4" Tall - 9/16" Bolt Hole
- Shop: MORryde Suspension Upgrade Kit for Triple Axle Trailers - 2-1/4" Long Shackle Straps
- Shop: MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 2-1/4" Long Shackle Straps
- Shop: Center Hanger for 2" Wide Slipper Springs - 4-1/2" Tall - 7/8" Bolt Hole
- Search Results: hd42656bx
- Search Results: stl8rb
- Shop: Suspension Enhancement
- Q&A: What is the Capacity of a Round Trailer Axle with a 3 Inch Diameter
- Q&A: Trailer Running Lights Do Not Work but Brake Lights and Turn Signals Do Work
- Q&A: Trailer Lights Left Side Turn Signal and Brake Lights Not Working
- Article: Trailer Wiring Diagrams
- Video: Redline Trailer Suspension - Leaf Spring Suspension - 093026 Review
- Video: Redline Trailer Suspension - Leaf Spring Suspension - 28-9-1 Review
- Article: Where to Position the Trailer Axle?
- Search Results: brake mounting bracket
- Search Results: brake mounting flange
- Video: Redline Trailer Suspension - Leaf Spring Suspension - 30-28 Review
- Search Results: suspension
- Q&A: Which 2-inch Hanger is Used for the Rear hanger Slipper Springs?
- Q&A: Grease Caps For Hubs on Lippert 7,000 lb Axles
- Q&A: Rear Slipper Spring Hanger Bracket 2 Wide Dexter 7000lb
- Q&A: Will Going to a Tire with Higher Ply Rating Prevent Blow Outs on a Livestock Trailer
- Search Results: grease cap
- Search Results: dust cap
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: Slipper Spring Trailer Suspension System Review
- Article: Most Popular Wheel Bearings