Replacement Marker Lamp Lens for Yakima Rack and Roll Trailer

Question

Question:

I have a rack and roll trailer. I need an amber replacement lens for the front side marker. You show Y8880178 as a replacement which includes the light. I dont need the light just the amber lens. Is it possible to get only the amber lens?

asked by: John D

0

Expert Reply:

I spoke with my Yakima representative, and was told that they do not offer the replacement lens as a separate item. Your best bet would be to order the # Y8880178 and replace the entire lamp.

expert reply by: Mike L

0

Answer 1

Since the height of your pintle-equipped military trailer is so much greater than the height of the hitch on your Honda Pilot (possibly as much as 2 feet) I am not sure there is any way to keep the trailer level when hitched. We do not offer an…

view full answer...

Answer 2

The Malone Trailer Tongue Kickstand #MPG467 is made to keep the trailer tongue 15 inches off the ground and is designed for Malone trailer tongues that are 2 inches wide by 3 inches tall. The Yakima Rack and Roll trailer has a tongue that is 2 inches…

view full answer...

Answer 3

The color of the lens of the Replacement Side Marker Light #Y8880178 that you referenced is amber. This is the replacement lens for the clearance light up near the front crossbar of the Rack and Roll trailers like part #Y08107.

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Marker Lamp Lens for Yakima Rack and Roll Trailer

Product Page this Question was Asked From

Continue Researching