Amperage Draw for Optronics LED Light part # ILL39CB

Question

Question:

How many amps does this LED require? Illuminating a 7x16 enclosed trailer into a camper.

asked by: Don

1

Helpful Expert Reply:

The LED Dome Light # ILL39CB that you referenced draws .669 amps when used with a 12 volt circuit like what would be on your camper and if used in a 24 volt setup would draw .217 amps.

expert reply by: Jameson C

1

Answer 1

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 2

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 3

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 9

The Global Link RV Entry Door Locking Latch Kit #295-000019 that you referenced would be the correct fit for your 2010 Keystone Montana as this is a fit for standard RV doors like what your Montana has. I attached a review video link for this latch…

view full answer...

Answer 10

On single axle trailers typically you put the hanger spacing right at 1/4 of an inch shorter than the leaf spring length from eye to eye center. So if you were using the leaf spring part #e54SR that you referenced which measures 25-1/8 inches long…

view full answer...

Answer 11

I believe I have a solution for you, but I think you may need to remeasure your cutout and/or compare the measurements of your current latch with one of ours. Since latches tend to be fairly universal in size when it comes to the RV world the Global…

view full answer...

Answer 12

The Hayes Air Actuated Trailer Brake Controller - 1 to 4 Axles - Proportional #HA100400C mounts to the inside of your 2007 Nemar Essex at the dash just like other electric brake controllers will. It needs to be installed on the inside of the vehicle…

view full answer...

Amperage Draw for Optronics LED Light part # ILL39CB

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching