Can a Superwinch Wiring Kit be Used with a Warn Winch

Question

Question:

Can this wiring kit be used with Warn Winches?

asked by: Sammy

0

Expert Reply:

Yes, you can use the wiring kit # BDW20207 with any winch up to 16,500 pound capacity. If your Warn winch is under 16.5K then you can use this kit. I have linked a video showing an example installation of this kit and a link to our help article on wiring an electric winch.

expert reply by: Michael H

0

Answer 1

For an Anbull 13000-lb winch, I recommend going with a 2 gauge wire like the Bulldog Winch Rear Wiring Kit - Quick Connect to Terminal End, part #BDW20207. It can handle any winch up to a 16.5K capacity. It is 24 feet long, which is the longest we…

view full answer...

Answer 2

The Trailer and Vehicle Electric Winch Wiring Kit #BDW20207 on your Badlands 12,000 winch will work well. The 2 AWG wire will be adequate for your winch as it is confirmed to work on Superwinch winches up to 16.5k in capacity.

view full answer...

Answer 3

I spoke with my contact at Bulldog Winch and he said that the #BDW20207 is designed for a 12 volt system that sees intermittent 400 amp use. He said that if you are looking for an alternative application for this it would be easier if you gave us…

view full answer...

Answer 4

The Bulldog Quick Connects #BDW20047 that you referenced are designed to be used on wire that is from 6-10 gauge. Since you have 6 gauge wire you would be just fine. This does not come with any wire, and to determine if your winch requires circuit…

view full answer...

Answer 5

What you need for your 12K winch is the trailer and vehicle electric winch wiring kit #BDW20207. It comes with everything you are looking for with 2 AWG Double Wire, consists of a 24 foot wire - runs from the rear of the vehicle to the battery, and…

view full answer...

Answer 6

I spoke to someone at Bulldog Winch and they said the reason the Anderson 175 amp disconnects can work in the Bulldog Winch Rear Wiring Kit, part #BDW20207, is because a winch is used intermittently. He said while the winch can draw up to 400 amps,…

view full answer...

Answer 7

I called my contact about the Electric Winch Wiring Kit, part #BDW20207. The wire is a 2-gauge stranded copper wire. Stranded wire is used because it is much more flexible than solid wire that size.

view full answer...

Answer 8

While it most likely would work, the Trailer and Vehicle Electric Winch Wiring Kit #BDW20207 has never been tested on your Badlands 12,000 winch so I could not say with 100 percent certainty if it would work for you. If your winch can be powered with…

view full answer...

Answer 9

Quick connectors like the #BDW20348 do come in different sizes depending on the gauge of wiring required for the application. There are a couple of different options for 2-4 gauge wiring that you can use that I've listed below for you to check…

view full answer...

Answer 10

A 2 gauge wire is only a little smaller than double aught (2/0) by about 0.11 inches diameter so it could be used in connector #PK11852. But I advise soldering in the wire and not crimping it for the best results. Triple aught (3/0) would be too…

view full answer...

Answer 11

First, the wiring on a trailer connector can provide a maintenance charge to a 12 volt battery on a trailer but it will not be able to fully charge it. The 12 volt circuit on a 7-Way is already circuit protected so a separate fuse or breaker should…

view full answer...

Answer 12

Yes, the ring terminal you see attached to the housing of the Pollak Single-Pole, Round Pin Trailer Wiring Connector #PK11852 that you referenced is used for a ground circuit. Check out the picture I attached that came from a customer who used this…

view full answer...