Possible Quick Connect Recommendation for a 12k Badlands Winch

Question

Question:

I want to put a quick connect on my 2003 Dodge 3500 for my winch. I have a 12000 lb bad lands winch what connects an size wire should i use??

asked by: William M

0

Expert Reply:

The Trailer and Vehicle Electric Winch Wiring Kit # BDW20207 on your Badlands 12,000 winch will work well.

The 2 AWG wire will be adequate for your winch as it is confirmed to work on Superwinch winches up to 16.5k in capacity.

expert reply by: Jameson C

0

Answer 1

The Bulldog Winch Receiver Mount Kit #BDW20155 has the standard 10 x 4.5" mounting bolt pattern which will match up exactly with your Badland Apex 12000. As for the wiring, you will need to route the wire from your 4Runner battery and mount…

view full answer...

Answer 2

I did some research and found instructions for installing the RanchHand Legend Grille Guard on your 2011 F-250 4x4. You can check out the attached photo that shows where a front hitch is mounted on a Ford F-250. You may find that the bottom bar on…

view full answer...

Answer 3

The dimensions on the Pollak 7-Circuit-Breaker Junction Box, part #PK52249, are as follows, With the mounting holes on the left and the right the length (right to left) from one edge of the mounting hole tab to edge of the other mounting hole tab is…

view full answer...

Answer 4

While it most likely would work, the Trailer and Vehicle Electric Winch Wiring Kit #BDW20207 has never been tested on your Badlands 12,000 winch so I could not say with 100 percent certainty if it would work for you. If your winch can be powered with…

view full answer...

Answer 5

What you need for your 12K winch is the trailer and vehicle electric winch wiring kit #BDW20207. It comes with everything you are looking for with 2 AWG Double Wire, consists of a 24 foot wire - runs from the rear of the vehicle to the battery, and…

view full answer...

Answer 6

To actually put a decent charge on your battery throughout the day the answer is a heavier gauge charge wire like what the part #BDW20207 has. This will carry enough amperage to put a solid charge on the battery between dumps. Normally this kit is…

view full answer...

Answer 7

For a great solution for boosting your fuel economy while towing on your 2016 Ram 1500 with a 5.7L hemi, I recommend the Edge Pulsar Inline Tuner with Insight CTS3 Monitor #EP28XR. Not only does the Pulsar include a simple plug-in setup without any…

view full answer...

Answer 8

The Furrion AC/DC Distribution Panel, #FDP12WABL can have up to 8 circuit breaker installed. AC distribution is maximum of 12 branches (7 for 30A main; 12 For 50A main). The AC main breakers are 30Amp or 50Amp x2.

view full answer...

Answer 9

For a winch like the Superwinch S6000 Winch #CU854754 you will simply want to use the Trailer and Vehicle Electric Winch Wiring Kit #BDW20207. Since winches can vary on how much they can pull this also affects how much power they need. For a winch…

view full answer...

Answer 10

The Badland winch 9k has a power draw of 300 amps at full load. You need a deep cycle 12V AGM battery that can handle that amperage. I recommend a battery with 650 Cold Cranking Amps (CCA). Badland Winches are an introductory winch with a not so…

view full answer...

Answer 11

Rolling capacity of a winch on flat ground is much higher like you mentioned. Basically you can take the capacity of the winch and multiply it by 10 to determine it's rolling capacity. So in your situation you could get away with a 380 lb winch…

view full answer...

Answer 12

In regards to the Bulldog Winch Rear Wiring Kit part #BDW20207, the length of ground wire is included to ensure a good ground on every application. The kits are not tailor made to any one particular application and not all customers will have a good…

view full answer...

Possible Quick Connect Recommendation for a 12k Badlands Winch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching