How Does Breakaway Cable of Titan Actuator Reset

Question

Question:

If the acuator has be set can it be rest or do you have to replace it

asked by: Greg

0

Expert Reply:

What do you mean reset? Do you mean like resetting the breakaway mechanism of the actuator?

To release the breakaway lever of the Titan Zinc-Plated Brake Actuator # T4747200 you will need to use a screw driver to push the clip on the lever back towards the rear of the trailer while pushing the lever back to its original position.

expert reply by: Jameson C

0

Answer 1

I spoke to my contact at Titan about resetting a Titan Model 60 actuator which is not the Dexter part #099-175-20. You have to remove the cover and then carefully remove the spring inside. Then set the lever in the disengaged position and re-insert…

view full answer...

Answer 2

I just called my contact at Titan and they told me that you should never use the DOT 5 fluid. They said if DOT 5 is used it will reduce the life of the seals in the unit by about 75 percent. They told me that DOT lll brake fluid should be used.

view full answer...

Answer 3

I will be happy to explain resetting the breakaway lever on the Titan Model 6 actuator, #T4747200. The manual states: Resetting the Break-away Lever: (Refer to the parts diagram in the instructions linked to the right). When the break-away lever…

view full answer...

Answer 4

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

We can definitely get you set up. For a 7-way wiring harness for your 2024 Honda Pilot trailsport I recommend the Curt T-Connector #C35ZV which will plug in to the existing tow package connector at the rear your vehicle. I do also recommend getting…

view full answer...

Answer 9

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

All the brake controller needs to sense a trailer connection so that you can test it is a slight amperage draw on the output circuit. For that you can use a circuit tester like the part #PTW2993 with one pin grounded and the other on the output pin.…

view full answer...

Answer 12

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

How Does Breakaway Cable of Titan Actuator Reset

Product Page this Question was Asked From

Continue Researching