How to Pick Out a Drop Curt Weight Distribution System Shank

Question

Question:

Help me pick the right weight distribution receiver. Curt 17123 or 17124. Ram 2500 to the top of receiver is 24 3/4 inches . Travel trailer bottom of ball socket is around 18. I figure since I havent hooked up at least a 1 inch weight when hooked up. What is the correct way to figure the product needed? Thanks.

asked by: Jerry M

0

Expert Reply:

Based on the two measurements you listed you would need a drop of 6-3/4 inches.

The part # C17123 that you referenced would work to give you the amount of drop you would need.

I also attached a help article that details how to pick out the correct rise/drop ball mount to tow a trailer level for you to check out.

expert reply by: Jameson C

0

Answer 1

The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached…

view full answer...

Answer 2

The weight distribution system I recommend with integrated sway control that will fit a 3" tall trailer frame is the Reese Steadi-Flex Weight Distribution System part #RP66558 which is a bolt-on option. In order to use this system you will also…

view full answer...

Answer 3

Yes, the Curt weight distribution shank #C17123 can be used with a Reese weight distribution head. Both have 3/4 inch diameter holes spaced 1-1/4 inches apart on center.

view full answer...

Answer 4

You will first want to check the fuses on your tow vehicle. Some vehicles could have fuses for operating the turn signals and brake lights of a towing package. You will want to check if they are installed and working properly. The next thing is to…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...