Where to Find Coupler Manufacturer Name

Question

Question:

where on my trailers coupler would I find the manufacturers stamp? On the registration, It states it is a 1995 Penn Utility trailer.

asked by: John

0

Expert Reply:

The manufacturer's name should be stamped somewhere on the coupler itself. The information is usually located on the top of the coupler, to the rear of the latch. The capacity of the coupler and the size ball the coupler is intended to be used with will be stamped there as well.

expert reply by: Mike L

0

Answer 1

Coupler Repair Kit #CA-5100-RK includes all parts needed to rebuild an etrailer brand or Ram brand 5K-rated 2-inch ball coupler with a trigger latch. It consists of all components other than the housing. If you have one of these models - #CA5100B,…

view full answer...

Answer 2

Though we do not carry coupler kits that are designed with your specific car hauler in mind, we do have the Repair Kit for etrailer and Ram A-Frame Couplers, part #CA-5100-RK, that you referenced. As the name states, this is designed with etrailer…

view full answer...

Answer 3

The Repair Kit for etrailer and Ram A-Frame Couplers #CA-5100-RK only fits the following couplers #CA5100B, CA-5100-BLB, and #CA-5100-Z, so it would not solve your connection difficulty, unless you had one of these specific couplers. Aside from…

view full answer...

Answer 4

If the trigger broke on your Pro Series A-Frame Trailer Coupler #PSE338050303 then you would need to replace the whole unit. I reached out to my contact at Pro Series who said that they unfortunately do not have carry any replacement parts for this…

view full answer...

Answer 5

Thank you for providing a photo of your trailer coupler. Trailers should always be level when hitched. If a trailer is out of level when towed it will tend to have more sway. I notice you have weight distribution (WD) lift brackets on your trailer…

view full answer...

Answer 6

We have a nice selection of repair kits available for A-frame trailer couplers. The kit you need will depend on what type of coupler you have and its manufacturer. For example, the etrailer Repair Kit #CA-5100-RK that you were looking at is designed…

view full answer...

Answer 7

We have a Fulton coupler repair kit with the part #F670801 that you'd want instead of the #CA-5100-RK which only fits the Ram brand of couplers.

view full answer...

Answer 8

There is not a universal latch repair kit. You will have to match the correct repair kit to the correct coupler. You are not able to use another brand repair kit on another brand coupler. Normally the coupler information is engraved on the coupler.…

view full answer...

Answer 9

The Repair Kit for etrailer and Ram A-Frame Couplers part #CA-5100-RK could very well work with the Fulton a-frame trailer coupler on your 2003 Coleman Cheyenne Folding Pop-Up Camper as the design is relatively the same. However, we have not yet…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 12

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Where to Find Coupler Manufacturer Name

Product Page this Question was Asked From

Continue Researching