Replacement Lead Leg Recommendation for an Atwood Landing Gear Set

Question

Question:

Looking for a replacement complete Atwood landing leg Lead for a 2000 McKenzie Medallion fifth wheel, From the top of the leg to bottom of outer housing it is 29 1/2 inches. Main leg from bottom of gear housing to end of outer leg is 27 1/2. 2 1/2 x 2 1/2 square tube. 15 1/2 inches between mounting stops. This has a single 12 v dc motor, I am only looking for the leg assembly, down leg and landing foot pad. Is there an Atwood leg that fits this? Thank you.

asked by: David P

0

Expert Reply:

The Stromberg Carlson Replacement Lead Jack w/ Drop Leg # LG-179013 that you referenced, is a direct replacement part for jacks from Stromberg Carlson, Lippert and Atwood.

This part's outer tube does measure 29-1/2-inches tall just like yours so it should work well for you.

expert reply by: Jameson C

0

Answer 1

For a replacement lead leg for your Atwood landing gear what you can use is the Replacement Lead Jack with Drop Leg #LG-179013. You just want to measure to make sure it is the right length, as this leg is 29-1/2 inches with a distance between the…

view full answer...

Answer 2

The division at Atwood that handled the jacks and landing gear was sold off to Lippert so direct replacement parts are not available. But it is likely that the gear box and motor of another brand will still fit. And yes, the gear box and motor do…

view full answer...

Answer 3

The 8K Landing Gear Set w/ Handle #RVLG-8HDL should fit just fine as it uses the standard weld stop locations measuring 15-1/2" or 17-1/2" for the mounting brackets. I don't know what the current bracket dimensions are for…

view full answer...

Answer 4

The etrailer Landing Gear Set, part #RVLG-8000 can be used to replace the landing gear set you have on your 2007 Montana. The hand crank is available as a separate item and is part #RVLG-HDL. Most landing gears are interchangeable but you can take a…

view full answer...

Answer 5

I reached out to my contact at Lippert who said that the Atwood line has been discontinued and they don't have any replacement parts for it. Since this is the case you'll need to replace your Atwood jack. Was this for the landing gear or for…

view full answer...

Answer 6

In order to rebuild the gears inside your landing gear legs you'll need the Lippert Components Venture Repair Kit for 5th Wheel RV Landing Gear part #LC146060 for follow leg or part #LC146059 for lead leg.

view full answer...

Answer 7

The replacement follow leg for your Venture landing gear on your 2007 Keystone is part #LG-179014. This outer tube measures 29-1/2 inches overall. If this matches your landing gear leg then the #LG-179014 leg will work for you.

view full answer...

Answer 8

Based on what your VMC900L has wrong with it the best option would be to replace the lead leg with part #LC119102.

view full answer...

Answer 9

Yes, for your landing gear leg that has a sticker that says VMC900R the part #LG-179013 is the correct replacement lead leg.

view full answer...

Answer 10

Yes we have confirmed for sure that the #LC119102 is the exact same as the LC241846 and would work for you.

view full answer...

Answer 11

For your VMC900R landing gear if you want to replace the lead leg I recommend the Replacement Lead Leg for Stromberg Carlson Landing Gear - 33-1/2" #LG-177202 and then for the follow leg #LG-177201. I've attached a photo of the measurements…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement Lead Leg Recommendation for an Atwood Landing Gear Set

Product Page this Question was Asked From

Continue Researching