Front Mount Receiver for a 2016 Ford F-350 4x4

Question

Question:

I purchased and installed a Curt Front Mount Hitch for a 4X4 2014 F-150. Will this hitch fit on a 2016 F-350 4X4 6.7 Diesel?

asked by: Keith W

0

Expert Reply:

Curt front mount trailer hitch # C31018 does fit the 2016 Ford F-350 4x4 models. I have also included a link to a video showing an example installation of this hitch for you. The front mount hitch for the 2014 F-150, # C31068, will not fit your 2016 F-350.

expert reply by: Michael H

0

Answer 1

The Curt Front Mount Trailer Hitch Receiver #C31018 is confirmed to fit your 2015 Ford F-350 if you have the 4WD model. The hitch center section can be installed in either a raised or lowered position. If you mount it in the lowered position, the…

view full answer...

Answer 2

The installion instructions for the Draw-Tite Front Mount Trailer Hitch Receiver part #65049 do not require that the front lower bumper spoiler be removed therefore yes, I believe you can leave it in position while you install the trailer hitch. The…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 5

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 8

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 9

Hey Robert, sorry it can be a bit confusing navigating all those facets for the camper tie downs, but I did go ahead and find those tie downs you were looking for. For the front, you'll want the TorkLift Camper Tie-Downs #TL87CR (TorkLift P/N…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

We do - for your 2023 Ford F-350 you'll want the TorkLift StableLoad Suspension Upgrade w Quick-Disconnect #TL89CR.

view full answer...

Answer 12

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Front Mount Receiver for a 2016 Ford F-350 4x4

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching