Fairing Recommendation for SportRack Roof Racks

Question

Question:

I was wondering if you guys have any wind fairings that fit part number sr1002

asked by: Jesse F

0

Expert Reply:

The Rhino Rack Fairing part # RRRF3 is a universal fairing that could be used on the Sportrack roof rack part # SR1002 that you referenced. This is a 44 inch fairing that should work well with the 50 inch bars of the # SR1002.

expert reply by: Jameson C

0

Answer 1

All roof racks do make noise. At highway speeds especially the least-noisy bar type is the elliptical shape, also known as an aero-style bar. These make less noise than round and square bars but they still make noise. We have a solution for your…

view full answer...

Answer 2

In order to carry 3 or 4 bikes on your 2008 Honda Fit Sport you will indeed need a roof rack. Trunk mount carriers won't work on your vehicle and the hitches offered for your car are only light-duty Class I types that can handle only two bikes…

view full answer...

Answer 3

The best way to pick out a fairing is to measure the distance between the feet of the rack and then go with the fairing that closest matches that distance but not over it. The Sportrack roof rack part #SR1010 that you referenced is an adjustable roof…

view full answer...

Answer 4

For a fairing that would fit the SportRack Semi-Custom Roof Rack #SR1008 I would recommend the Rhino-Rack Fairing #RRRF2. This is a 38 inch long fairing that will greatly reduce the wind noise created by your roof rack that will fit the #SR1008.

view full answer...

Answer 5

Good news, I have a solution for your 2008 Honda Fit's roof rack. The SportRack #SR1002, is a semi custom roof rack designed to fit different types of vehicle's roofs with the already included pads and clamps. You would just need to make a…

view full answer...

Answer 6

Wind noise is pretty normal with the installation of a roof rack, but what you can do is install a fairing like part #RRRF2 and the wind noise will be greatly reduced. Fairings are designed to direct the air over the rack to prevent the noise.

view full answer...

Answer 7

For your 2005 Honda Accord 4-door, I recommend the SportRack Semi-Custom Roof Rack, part #SR1002. This easy to install roof rack has adjustable footpads, and when used with the numbering system inscribed on the crossbars, makes the rack easier to…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...