Trailer Hitch and Wiring for a 2016 Subaru WRX Limited

Question

Question:

I want to confirm that this will fit a 2016 Subaru wrx limited. Also is there any pictures with the hitch insalled that i could look at? Does the rear bumper need to be removed when installing the hitch? Thanks

asked by: Adam

0

Expert Reply:

I checked with Curt and trailer hitch # C11408 is indeed listed as a fit for your 2016 Subaru WRX Limited. There is one picture from the instructions which I have added for you. I have also linked the instructions. You will not have to remove the bumper to install the hitch.

If you plan on doing some towing the correct ball mount is # C45521. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring you can use # C56259 to add a 4-Way flat connector.

If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch.

Curt also says you have to use stabilization strap # 18050 when using this hitch for any non-trailer load (such as a bike rack or car go carrier) per their warranty requirements.

expert reply by: Michael H

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 5

When it comes to a trailer hitch receiver for your 2015 Subaru WRX, a 1-1/4 inch Class I hitch, part #C11408, is the only one available. A 2 inch hitch is not available for the 2015 Subaru WRX. If you are planning to use the hitch to transport…

view full answer...

Answer 6

There is a Curt hitch that is a confirmed fit for both the 2015 Subaru Impreza (hatchback and single exhaust models) and the 2015 Subaru Crosstek XV, but it is a Class I hitch. Check out Curt trailer hitch #C11286. This hitch is great for light…

view full answer...

Answer 7

That's a tricky question that would be very difficult to answer. The hitches are designed to fit around a stock exhaust. If your aftermarket exhaust sits exactly where the stock exhaust would, then the #306-X7257 EcoHitch would fit perfectly for…

view full answer...

Answer 8

The EcoHitch Invisi Trailer Hitch Receiver part #306-X7257 weighs about 30 lbs. The good thing is the weight of the hitch itself does not count towards any weight capacities of your vehicle because it is attached to the frame. I have attached an…

view full answer...

Answer 9

Good question, and the Curt Trailer Hitch Receiver #C84ZV that fits your 2022 Subaru WRX will come out underneath the bumper and not through a bumper cut out. Curt doesn't have a great photo of this installed, so I added a cut out below from the…

view full answer...

Answer 10

The EcoHitch Invisi Trailer Hitch Receiver - Custom Fit - Class III - 2", part #306-X7211, does not have a back. The stinger arm from the Thule T2 Pro XTR Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount, part #TH83JV, may extend from the…

view full answer...

Answer 11

Since from what it sounds like, your Highlander doesn't have the factory tow package that includes a 7-way on the rear bumper, you'll need to do a hardwire installation. For starters, you'll need a functional 4 pole trailer wiring…

view full answer...