Where Does a Brake Controller Plug Into on a 2004 Ford F-350

Question

Question:

Where is the connection for brake controller on a 2004 Ford F-350

asked by: Tom B

0

Expert Reply:

On your 2004 Ford F-350 the factory port to plug in a brake controller is located near the center console to the right of the steering column. I have linked a video that shows how to access it.

expert reply by: Michael H

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Answer 4

Hello Dan, I can definitely help with this. It is completely normal for the Curt TriFlex brake Controller #C24VV to show the current gain setting when the brakes are applied, or when the manual override is pressed. It sounds like you have the gain…

view full answer...

Answer 5

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 6

We sure do! The etrailer Electric Trailer Brakes item #AKEBRK-35 work with 3,500 lbs axles that have a 4 bolt mounting flange. These left and right 10" x 2-1/4" assemblies have rust-resistant, e-coated backing plates that work with 15"…

view full answer...

Answer 7

Since you already have a factory 4-way flat on your 1996 Ford F-350 you will need the Adapter 4-Pole to 7-Pole #37185. This will plug into your factory 4-way and the rest of the wiring will have to be spliced into your factory wiring as I do not see…

view full answer...

Answer 8

To install your Reese Pod brake controller in your 2018 Ford Explorer will require the install harness part #3035-P which is a confirmed fit. If you check out the 9:55 mark of the install video I attached to this page you'll see where to find the…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

The Bulldog Powered-Drive Kit part #BD1824180100 is for two speed jacks whereas the Bulldog Powered-Drive Kit part #BD1824200100 is for single speed jacks. However, we can only confirm that these work with Bulldog jacks that have a 12,000 lb support…

view full answer...

Answer 11

I apologize for the confusion. It sounds like you have found some conflicting answers in the past, so I took the liberty to contact Bulldog directly and this is what they said: "The 12k RAM jack has a smaller diameter cross-shaft, therefore the…

view full answer...

Answer 12

Your 2014 Fleetwood Bounder should be on a Ford F-53 chassis. If you found the gray plug next to the brake release (see attached photo) then this means that you should just be able to use a plug-in adapter to easily install your brake controller. Out…

view full answer...

Where Does a Brake Controller Plug Into on a 2004 Ford F-350

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching