Curt Hitch Cover for a 2 inch Hitch

Question

Question:

if I buy a class 3 tow hitch, what is the plastic cover size I need?

asked by: Sam O

0

Expert Reply:

For a similar hitch cover that would fit a 2 inch hitch like the part # C22271 that you referenced you would want the part # C22272 instead.

expert reply by: Jameson C

0

Answer 1

You can add a license plate holder and light to your ramped utility trailer either with a single item such as #LPL55CB or #PM436B, or you can choose separate plate holders and lights to let you choose the designs you most prefer, such as plate holder…

view full answer...

Answer 2

I don't have any information specific to any one particular trailer but what I can tell you is that most license plates are mounted under the driver side tail light. In fact, most driver side tail lights even have a bracket for the license plate…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Based on the information I could find for the DICO 45264 is was popular on ShoreLand'r trailers. This would require the Idler Hub #AKIHUB-545-35-G-EZ-K with the Grease Seal #168255TB used instead of the seal included with the hub. We currently do…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

There's not many differences between the Air Lift WirelessONE item #AL25980EZ and item #AL25980. The main difference is that the item #AL25980EZ has a slightly higher CFM at 1.03 compared to 0.92 and it runs slightly more efficient at 9% over 15%…

view full answer...

Answer 9

Hey Buddy, so the Fastway Adjustable Ball Mount part #DTSTBM6825-2S is a really great choice for the 2-1/2 inch hitch of your 2021 Ford F-250 which is going to be very solid in your hitch due to it's built in anti-rattle device that is easy to…

view full answer...

Answer 10

For the Edge CS2 Evolution Diesel Tuner you will need to enter the programming menu. You will turn on your vehicle without starting it. Then use the Menu button to open the main menu and scroll down with the arrow to the Programming on the screen.…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Curt Hitch Cover for a 2 inch Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching